Multiquip tp24 manual Shut down Procedure, Wait for the cutting blade to stop rotating

Page 23

operation

3.Push the cutting table with the material, slowly and evenly until the cut is complete. Move the cutting table back and remove the cut pieces.

4.Avoid overloading the motor when cutting. However, the electric motor is protected with a manual-reset thermal overload switch that will turn the saw off if the motor is overheated. In the event that the switch is tripped, turn the “ON/OFF” switch to the “OFF” position and allow the motor to cool before attempting to restart.

Shut down Procedure

1.Place the power ON/OFF switch (Figure 16) in the OFF position (down).

Figure 16. Power ON/OFF Switch (OFF)

2.Wait for the cutting blade to stop rotating.

3.Disconnect the saw's AC power cord from the power source. NEVER leave the saw connected to a power source when unattended. This will prevent accidental starting.

4.Using a soft cloth, clean any excess debris or residue that may have accumulated on the saw.

5.Store saw in a clean dry location where it will be out of the reach of children.

TP24 TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 23

Image 23

Contents Model TP24 Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24 Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyTranSporTIng SaFeTy ELeCTrIC moTor SaFeTyPower Cord/Cable Safety LIFTIng SaFeTy3200 SpecificationsDimensions DimensionsDry Cutting Applications Accessories/Replacement PartsFeatures General informationTP24 Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Saw Set-Up Support Stand Assembly OptionalElectric motor components/set-up Electric Motor ComponentsRefer to Figure Connecting the water PumpInstall drain plug in water tray Set-upCutting Depth BladesBlade Components Blade Installation Never grab or touch a live Power cord with wet hands, Connecting the PowerSawing Guides Using the Cutting Table Place the power ON/OFF switch in the OFF position downPerforming Miter Cuts Using the Rip GuideSawing guides Performing Diagonal CutsStarting or attempting to operate the saw Start-up ProcedureOperation Wait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter not using the machine for a prolonged period of time Maintenance intervalsAfter wet cleaning and before using the machine again Before not using the machine for a prolonged period of timeTake off the old belt and replace with new belt Water pump maintenanceBelt replacement Bearing housing removalBearing Housing Removal Bearing Housing InstallationForth. If the table binds against the rail at any Realignment MethodIntially, but shifts apart as the table travels along Rail, proceed to MethodShim may be required Further adjustment-repeat stepMethod Table from the guide rails. See FigureTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Belt Switch, toggle 15ASuggested Spare Parts TP24 tile saw with electric motor 1 to 3 unitsMain SAW Assy Part Name Cutting Head Assy Cutting Head Assy Electric motor Assy QTY Remarks Cutting table assy Part Name QTY Blade guard assy Part Name Bearing housing assy Bearing housing assy Switch box assy Remarks Tools and accessories TPSDT1010st TP100102FreIgHT poLICy Terms and Conditions of Sale PartsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help