Multiquip tp24 manual Bearing Housing Installation, Bearing Housing Removal

Page 27

MAINTENANCE

BELT

GUARD

BELT

ADJUSTMENT

SCREW

PULLEY

BEARING

HOUSING

INNER

FLANGE

Figure 19. Bearing Housing Removal

Bearing Housing Installation

To install a new bearing housing, perform the following:

1.Make sure that the old housing has been properly removed.

2.Unpack the new bearing housing and place the flat portion face-down on a towel situated on a flat surface.

3.Secure the cutting head in a in a completely horizontal position.

4.Slide the new bearing housing with the flat portion facing upwards onto the 4 screws located below the mounting plate. Take care not to damage the inner flange. Lock the bearing housing into place by using the brackets and nuts.

5.Pull the motor towards you, place the belt on the pulleys, and tighten the motor position adjustment screw. Be sure to leave some slack on the belt.

6.Align the belt by adjusting the motor pulley after loosening the hex screw.

WARNING

Do not adjust the bearing housing pulley.

7.After aligning the belt, tighten the hex screw.

8.Replace the belt guard and lock into place using 4 screws.

TP24 TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 27

Image 27

Contents Model TP24 Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24 Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyTranSporTIng SaFeTy ELeCTrIC moTor SaFeTyPower Cord/Cable Safety LIFTIng SaFeTy3200 SpecificationsDimensions DimensionsDry Cutting Applications Accessories/Replacement PartsFeatures General informationTP24 Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Saw Set-Up Support Stand Assembly OptionalElectric motor components/set-up Electric Motor ComponentsRefer to Figure Connecting the water PumpInstall drain plug in water tray Set-upBlades Blade ComponentsCutting Depth Blade Installation Never grab or touch a live Power cord with wet hands, Connecting the PowerSawing Guides Using the Cutting Table Place the power ON/OFF switch in the OFF position downPerforming Miter Cuts Using the Rip GuideSawing guides Performing Diagonal CutsStart-up Procedure OperationStarting or attempting to operate the saw Wait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter not using the machine for a prolonged period of time Maintenance intervalsAfter wet cleaning and before using the machine again Before not using the machine for a prolonged period of timeTake off the old belt and replace with new belt Water pump maintenanceBelt replacement Bearing housing removalBearing Housing Removal Bearing Housing InstallationForth. If the table binds against the rail at any Realignment MethodIntially, but shifts apart as the table travels along Rail, proceed to MethodShim may be required Further adjustment-repeat stepMethod Table from the guide rails. See FigureTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Belt Switch, toggle 15ASuggested Spare Parts TP24 tile saw with electric motor 1 to 3 unitsMain SAW Assy Part Name Cutting Head Assy Cutting Head Assy Electric motor Assy QTY Remarks Cutting table assy Part Name QTY Blade guard assy Part Name Bearing housing assy Bearing housing assy Switch box assy Remarks Tools and accessories TPSDT1010st TP100102FreIgHT poLICy Terms and Conditions of Sale PartsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help