Multiquip tp24 manual Set-up, Connecting the water Pump, Refer to Figure

Page 17

set-up

Figure 5. Support Stand Assembly

connecting the water Pump

Refer to Figure 6.

4.Attach the water hose coming from the blade guard and bearing housing to the water pump.

5.Install drain plug in water tray.

6.Fill the water tray with clean fresh water. The water pump intake must always be fully covered by water. Also, keep the pump intake free of sludge, debris and other materials that may accumulate in the tray.

7.Make certain that the water hose will not come in contact with the blade or interfere with any moving parts.

BLADE

GUARD

WATER WATER

PUMPHOSES

DRAIN

PLUG

BEARING

HOUSING

8.Insert the water pump power plug into the outlet cable receptacle from the electric motor conduit box as shown in Figure 7.

ELECTRIC MOTOR

CONDUIT BOX

CONDUIT

BOX

CABLE

RECEPTACLE

POWER

PLUG

WATER

PUMP

Figure 7. Water Pump Power Connection

WARNING

Disconnect the pump before attempting to handle the pump. NEVER operate pump without water in the tray.

NOTICE

The above procedure is for wet cutting applications only. NEVER dry cut with the pump connected to an AC power source. Running the pump dry will damage the pump. ALWAYSdisconnectthepump’spowercordwhendrycutting.

Figure 6. Connecting the Water Pump

TP24 TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 17

Image 17

Contents Model TP24 Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24 Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyPower Cord/Cable Safety ELeCTrIC moTor SaFeTyLIFTIng SaFeTy TranSporTIng SaFeTy3200 SpecificationsDimensions DimensionsFeatures Accessories/Replacement PartsGeneral information Dry Cutting ApplicationsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Electric motor components/set-up Support Stand Assembly OptionalElectric Motor Components Saw Set-UpInstall drain plug in water tray Connecting the water PumpSet-up Refer to FigureCutting Depth BladesBlade Components Blade Installation Sawing Guides Using the Cutting Table Connecting the PowerPlace the power ON/OFF switch in the OFF position down Never grab or touch a live Power cord with wet hands,Sawing guides Using the Rip GuidePerforming Diagonal Cuts Performing Miter CutsStarting or attempting to operate the saw Start-up ProcedureOperation Wait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter wet cleaning and before using the machine again Maintenance intervalsBefore not using the machine for a prolonged period of time After not using the machine for a prolonged period of timeBelt replacement Water pump maintenanceBearing housing removal Take off the old belt and replace with new beltBearing Housing Removal Bearing Housing InstallationIntially, but shifts apart as the table travels along Realignment MethodRail, proceed to Method Forth. If the table binds against the rail at anyMethod Further adjustment-repeat stepTable from the guide rails. See Figure Shim may be requiredTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Suggested Spare Parts Switch, toggle 15ATP24 tile saw with electric motor 1 to 3 units BeltMain SAW Assy Part Name Cutting Head Assy Cutting Head Assy Electric motor Assy QTY Remarks Cutting table assy Part Name QTY Blade guard assy Part Name Bearing housing assy Bearing housing assy Switch box assy Remarks Tools and accessories TPSDT1010st TP100102FreIgHT poLICy Terms and Conditions of Sale PartsTP24 Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help