Multiquip TP7X Electric motor components/set-up, Electric Motor Components, Saw Set-Up, Base

Page 16

electric motor components/set-up

Electric Motor Components

Figure 3 shows the location of the components of the electric motor.

115 VAC, 60 Hz

SINGLE -PHASE

ELECTRIC MOTOR

OVERCURRENT

BREAKER BUTTON

ELECTRIC WATER

ELECTRIC

PUMP AC

MOTOR

RECEPTACLE

ON/OFF SWITCH

Figure 3. Electric Motor Components

Saw Set-Up

WARNING

Whenever cleaning, adjusting or lubricating any part of the saw, make certain to place the power ON/OFF switch in the OFF position and disconnect the plug from the power source.

1.Open the shipping container carefully, lift the saw by its carrying handles and place it on a suitable table or platform. Make sure the table or platform can support the weight of the saw.

2.Make sure that the following items are found in the container:

„„Saw

„„Saw Blade

„„Water Tray

„„Water Pump

„„Drain Plug

„„Owner’s Manual

„„Universal Wrench

„„MasterGuide Template

 

Base

3.Slide water pump onto U-shaped bracket located at the bottom of the frame. See Figure 6.

4.Slide cutting head onto the post. Secure cutting head to the shaft using provided flat washer, lock washer and nut. Attach cutting depth control knob and washers to the cutting head through the slot located underneath the belt guard. See Figure 4.

5.Mount blade guard onto shaft protruding from the side of the cutting head. Secure the blade guard in place using the provided serrated washer and blade guard knob.

CUTTING

HEAD

BLADE

GUARD

KNOB

 

BLADE

SHAFT

GUARD

 

CUTTING

DEPTH

CONTROL

KNOB

WATER

TRAY

Figure 4. Saw Assembly

6.If using the optional support stand, assemble as described in the Support Stand Assembly section. Make sure that the saw is secured on the support stand as instructed.

support Stand Assembly (Optional)

Refer to Figure 5 for location of components.

1.Remove the folding stand from its box.

2.Swing the working bench upright. Open the two legs and place the work bench on top of the folding stand.

3.After teh saw stand is assembled, seat the saw securely on top of the stand.

page 16 — TP7X TILE SAW • operation manual — rev. #0 (03/04/11)

Image 16
Contents Model TP7X Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningSpecifications are subject to change without notice Table of ContentsSawing Guides Page Safety Information SaFeTy meSSageSGeneraL SaFeTy SaW SaFeTy BLaDe SaFeTyELeCTrIC moTor SaFeTy Power Cord/Cable SafetyLIFTIng SaFeTy TranSporTIng SaFeTySaw Specifications Electric Motor SpecificationsDimensions DimensionAccessories/Replacement Parts FeaturesGeneral information Dry Cutting ApplicationsPage Saw components Saw ComponentsStopper Place stopper in water tray when filling with water Support Stand Assembly Optional Electric motor components/set-upElectric Motor Components Saw Set-UpConnecting the water Pump Install drain plug in water traySet-up Refer to FigureBlades Blade ComponentsCutting Depth Blade Diameter vs. Cutting DepthSee for proper blade use guidelines Blade InstallationProper Blade Use Connecting the Power Sawing Guides Using the Cutting TableUsing the MasterGuide Template Base Set-up/sawing guidesUsing the Rip Guide Sawing guidesPerforming Diagonal Cuts Performing Miter CutsOperation Start-up ProcedureStarting or attempting to operate the saw Shut down Procedure Wait for the cutting blade to stop rotatingBasic Maintenance Inspect the cutting table periodically. Replace worn partsMaintenance intervals After wet cleaning and before using the machine againBefore not using the machine for a prolonged period of time After not using the machine for a prolonged period of timeBelt Replacement Water pump maintenanceBearing housing removal Bearing Housing Installation Bearing Housing RemovalWiring diagram electric motor Electric Motor Wiring DiagramPage Troubleshooting blade Blade TroubleshootingTroubleshooting Saw Saw TroubleshootingHERE’S HOW to GET Help