Singer 6184-01, 6184-21 manual Operation

Page 7

OPERATION

WARNING!

To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool before changing accessories or making adjust- ments.

Adjusting the Depth of Cut (Fig. 4)

The shoe assembly can be moved to change the depth of cut. Cut-off wheels wear down as they are used and the depth of cut may need to

be adjusted.

Wing nut

Fig. 4

Wing nut

Shoe assembly

Lower shoe assembly for shallower cuts.

Raise shoe assembly for deeper cuts.

1.Unplug tool.

2.To change the depth of cut, loosen the wing nuts on shoe assembly (counterclockwise).

3.Position the depth of the shoe assembly for deeper or shallower depth (Fig. 4).

NOTE: Make repeated passes at depths of less than 1/2" to achieve the desired depth. Cutting at a depth of more than 1/2" will damage the wheel.

4.Tighten the wing nuts securely (clockwise).

NOTE: The MILWAUKEE Hand-Held Abrasive Cut-Off Grinder is de- signed to cut metal and non-metallic materials. It is NOT recommended for cutting wood. DO NOT attempt to install a saw blade on the tool. DO NOT use with liquids or in damp locations.

Starting and Stopping the Tool

The tool operates at no load speed of 4350 RPM.

1.Plug in tool.

2.To start the tool, pull the trigger.

3.To stop the tool, release the trigger.

Preventing Kickback

Kickback is the sudden reaction to a pinched wheel which could cause a cut-off grinder that is not under control to lift up and out of the work- piece towards the user. Take the precautions below to help prevent kickback.

1.Maintain a firm grip and correct body position. Position arms and body to control the backward and upward reaction force of kickback. Control the cut-off grinder at all times.

2.Set the depth of cut for no more than necessary. The less wheel exposed, the less chance of binding and kickback. Before cutting, be sure shoe assembly is tight.

3.Always allow the blade to come to a full stop before remov- ing the cut-off grinder from the workpiece. Never remove the cut-off grinder from a cut while the blade is moving. If restarting or correcting direction in mid-cut, allow the blade to coast to a stop, back the cut-off grinder up a few inches and center it in the kerf before restarting.

4.Stay alert. Any distraction can cause twisting or binding. Repetitive cuts may lull the user into careless movements.

5.Do not force the tool. Forcing a cut-off grinder reduces control and cutting efficiency.

If kickback should occur, continue to grip the cut-off grinder firmly and immediately release trigger.

WARNING!

Only use abrasive and diamond cutting wheels with a maximum safe operating speed greater than the RPM marked on the tool's nameplate.

Wheel Selection

Non-metallic Materials

When cutting non-metallic materials, use a silicone carbide abrasive cut- off wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUP- PLIED WITH CUT-OFF WHEEL. Always wear a dust mask.

Metallic Materials

When cutting metals, use an aluminum oxide abrasive cut-off wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUPPLIED WITH CUT- OFF WHEEL. Protect everyone in the area from sparks.

Masonry Materials

When cutting masonry materials, use dry diamond wheels or silicone carbide abrasive cut-off wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUPPLIED WITH CUT-OFF WHEEL. Always wear a dust mask.

Making a Cut

1.Unplug tool. Select a cutting depth and adjust the height of the shoe assembly as described in “Adjusting the Depth of Cut”.

2.Plug the tool in and pull the trigger. Allow the motor to reach full speed and then slowly lower the wheel into the workpiece.

NOTE: Always start the cut gently; do not bang or bump a wheel when starting the cut.

3.While cutting, keep the shoe flat against the workpiece and maintain a firm grip. Do not force the cut-off grinder through the work. Forc- ing a cut-off grinder can cause kickback.

Make repeated passes at depths of less than 1/2" to achieve the desired depth. Cutting at a depth of more than 1/2" will damage the wheel. Frequently clean dust from air vents and guards.

4.When the cut is finished, always allow the motor to come to a complete stop. Never remove the cut-off grinder from a cut while the blade is moving.

5.If making a partial cut, restarting a cut or correcting cut direction, allow the wheel to come to a complete stop. To resume cutting, center the wheel in the kerf (cutting slot), back the saw away from cutting edge a few inches, pull the trigger and re-enter the cut slowly.

NOTE: If the cut-off grinder stalls, maintain a firm grip and release the trigger immediately. Correct the problem before continuing.

page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operators Manual Service General Safety Rules Read and Understand ALL InstructionsElectrical Safety Personal SafetyWheel Instructions Cut-Off Grinder Capacities Cat Wheel FunctionaldescriptionArbor Hole Size At least Thickness 6184-01 5000 Or 20 mm Extension Cords GroundingInstalling and Removing Shoe Fig Tool AssemblyInstalling Side Handle Operation Accessories MaintenanceWarranty Sécurité DES Personnes Conservez CES Instructions Aire DE TravailSécuritéélectrique Utilisation ET Entretien DES OutilsInstructions relatives aux disques Mesures DE Sécurité Spéciales20 mm DescriptionfonctionnelleDirectives pour l’emploi des cordons de rallonge Calibres minimaux recommandés pour Les cordons de rallongeMise À LA Terre Avertissement Cordons DE RallongeMontage DE Loutil Avertissement Installation et retrait des disques à tronçonner FigInstallation et retrait de la semelle Fig Installation de la poignée latéraleManiement Avertissement Accessoires Avertissement Maintenance AvertissementGarantie Seguridad Personal Guarde Estas Instrucciones Area DE TrabajoSeguridadelectrica USO Y Mantenimiento DE LA HerramientaInstrucciones para el disco abrasivo Reglas Especificas DE Seguridad20mm DescripcionfuncionalCapacidades de la disco abrasivo Catálogo Extensiónes Eléctricas Tierra ¡ADVERTENCIAGuías para el uso de cables de extensión Cómo instalar y sacar la zapata Fig Ensambaje DE LA Herramienta ¡ADVERTENCIACómo instalar el mango lateral Operacion ¡ADVERTENCIA Garantia Mantenimiento ¡ADVERTENCIAReparaciones Accesorios ¡ADVERTENCIA United States

6184-21, 6184-01 specifications

The Singer 6184-01 and 6184-21 sewing machines represent a blend of classic design and modern technology, catering to both novice and experienced sewists. Renowned for their reliability, these machines offer a host of features that enhance the sewing experience and make them suitable for various projects.

One of the standout characteristics of the Singer 6184 series is its robust construction. The machines are built with a sturdy metal frame that not only ensures longevity but also minimizes vibration during use, resulting in more accurate stitches. This stability allows users to tackle heavier fabrics with ease, such as denim and canvas, making these models versatile choices for a range of sewing applications.

The 6184 series is equipped with a powerful motor that provides consistent sewing speed, ensuring smooth operation across different fabric types. With multiple stitch options, including straight, zigzag, and decorative patterns, the machines offer flexibility for creative projects. Each model features a user-friendly dial interface that allows for quick stitch selection, making it easy for beginners to navigate.

Another key feature of the Singer 6184 series is the automatic needle threader, which simplifies the threading process and saves time. Additionally, the top drop-in bobbin system is designed for easy bobbin changes and prevents tangling, giving users confidence while sewing. The clear cover over the bobbin area allows for easy monitoring of thread levels.

The 6184-21 model includes advanced features such as adjustable stitch length and width, allowing for full customization based on individual project needs. This flexibility is complemented by a heavy-duty presser foot that provides excellent fabric feed, ensuring even stitching regardless of the material.

Both models come with a range of accessories, including multiple presser feet, a seam ripper, and an instructional manual that guides users through the machine’s features. These accessories enhance the sewing experience, enabling users to expand their skills and experiment with various techniques.

In conclusion, the Singer 6184-01 and 6184-21 sewing machines stand out in the market for their durability, ease of use, and advanced features. With a combination of classic craftsmanship and modern technology, these machines are ideal for anyone looking to embark on their sewing journey or expand their existing skills, making them a reliable choice for crafters of all levels.
Top Page Image Contents