Bryant Physical Data, Operating Weight Distribution Center of Gravity, Unit 502A, Dimensions

PHYSICAL DATA

UNIT 502A	024	036	048	060
SHIPPING WEIGHT (lb)*	560	590	690	700
OPERATING WEIGHT (lb)
Base Unit	450	480	580	590
REFRIGERANT TYPE		R-22
Operating Charge (lb)†	5.4	5.5	8.0	7.6
COMPRESSOR — TYPE		Scroll
Quantity...Model	(1)...ZR23	(1)...ZR34	(1)...ZR49	(1)...ZR57
Oil (oz)	24	42	48	54
HPS Setting (psig)
Cutout		426 ±	7
Reset		320 ± 20
LPS Setting (psig)
Cutout		27 ± 4
Reset		67 ± 7
CONDENSATE DRAIN CONNECTION
Size (in.)...Type		3/4...FPT
CONDENSER FAN	Centrifugal — Direct Drive		Centrifugal — Belt Drive
Nominal Cfm	1350	1350	2250	2450
Maximum Rpm	1100		1500
Blower Size (in.)	12 x 6		12 x 9
Pulley Pitch Diameter (in.)
Blower	None	5.0	6.0	6.0
Motor (Variable)	None	2.4-3.4	1.9-2.9	2.4-3.4
Motor Hp	1/2	3/4	1	11/2
Motor Rpm	825	1725	1725	1725
EVAPORATOR AIR FAN (Standard)		Centrifugal — Direct Drive
Nominal Cfm	800	1200	1600	2000
Max Rpm	1100	1150	1050
Blower Size (in.)	10 x 5	10 x 6	10 x 6
Motor Hp (Rpm)	1/6 (850)	1/2 (1075)	3/4 (1050)
EVAPORATOR AIR FAN (Optional)			Centrifugal Belt Drive
Nominal Cfm			1600	2000
Max Rpm			1300
Blower Size (in.)			10 x 8
Motor Hp	Not		11/2
Motor Rpm	Available		1725
Pulley Pitch Diameter (in.)
Blower			4.2
Motor (Variable)			2.4-3.4
CONDENSER COIL		Copper Tubes — Aluminum Fins
Size (L x H) (in.)	40 x 15	40 x 16	40 x 22
Number of Rows...Fins/in.	4...13.6	4...17	4...13.6
EVAPORATOR COIL		Copper Tubes — Aluminum Fins
Size (L x H) (in.)	34 x 15	34 x 16	34 x 22
Number of Rows...Fins/in.	4...14.4	4...15	4...14.4
INDOOR-AIR FILTERS		Factory-Supplied Cleanable Type
Number...Size (in.)	1...14 x 34 x 1		1...21 x 34 x 1
INTERCONNECTING TUBING SIZE (in.)**
Hot Gas	1/2	1/2	1/2	1/2
Liquid	3/8	3/8	3/8	3/8

LEGEND

HPS — High-Pressure Switch

LPS — Low-Pressure Switch

*Shipping weights include base unit plus packaging.

†If components are to be split, additional refrigerant will be needed. **Use Type L copper only.

NOTE: If components are to be split, the maximum length of refrigerant tubing to be used is 50 equivalent ft, assuming components will be installed in same horizontal plane. If components are not to be installed in same horizontal plane, contact your Bryant rep- resentative for more information.

NOTE: Fasten threaded rods through holes in end frames. Use 2 rods on each side of unit for a total of 4.

All panels must be in place when rigging.

OPERATING WEIGHT DISTRIBUTION AND

CENTER OF GRAVITY

UNIT		WEIGHT (lb/kg)				DIMENSIONS
		OF CORNER				(ft-in./mm)
502A
	1	2	3	4		A		B
024	93/42	108/49	139/63	120/54	2-5	/737	2-15/ /651
								8
036	95/43	113/51	148/67	124/56	2-43/ /730		2-2	/660
						4
048	112/51	143/65	183/83	142/64	2-5	/737	2-3	/686
060	114/52	143/65	186/84	147/67	2-43/ /730		2-23/ /679
						4		4

3