Grizzly G0700 owner manual Installing main blade

Page 25

11.Remove the shipping brace from the sliding table, then install the sliding table end cover over the fixed part of the sliding table end, as shown in Figure 17, using the premounted hardware. (Save the brace for future trans- port needs.)

Remove

Shipping Brace

Install End

Cover

Figure 17. Sliding table shipping brace and end

cover installed.

12.Attach the push handle assembly, as shown in Figure 18, with the two button head screws and flat washers already installed in the mounting holes.

Button Head

Cap Screws

Figure 18. Sliding table handle attached to end

of sliding table.

13.Thread (2) M5-.8 x 12 cap screws with 5mm lock washers through the switch bracket and into the sliding table base (see Figure 19), then tighten the cap screws.

Model G0700 (Mfg. since 8/09)

Magnetic

Switch

Figure 19. Magnetic switch installed.

14.Open the cabinet door and remove the motor shipping brace shown in Figure 20, then replace the fasteners where they were. (Save the brace for future transport needs.)

Figure 20. Motor shipping brace.

15.Tilt the blade assembly to 0˚, then move the sliding table out of the way so you can access the lower blade guard cover and blade arbors.

16.Insert the arbor lock tool into the hole shown in Figure 21, rotate the arbor until the arbor lock tool seats, then install the main blade per the instructions on Page 35 as a guide.

Arbor

Lock

Tool

Figure 21. Installing main blade.

-23-

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model G0700 Sliding Table SAW Page Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionIdentification Machine Data Sheet Other Related Information SlIdINg TABle SAW CAPACITIeS Safety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety for Sliding Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are ways to avoid the most common causes of kickback Glossary of Terms Availability Power SupplyFull-Load Current Rating Circuit Requirements forExtension Cords Grounding InstructionsMinimum Gauge Size 10 AWG 50 ftSetup Safety Unpacking SetupItems Needed For Setup Description QtyHardware Recognition Chart Inventory Item Figure Qty Rip Fence Round Rail AssemblyItem Figure Qty Table Saw Item Figure QtyFasteners Grouped by Usage Qty Push Handle Assembly w/LockBefore cleaning, gather the following CleanupSite Considerations To remove the saw from the pallet Moving & Placing Table SawMounting rip fence scale Installing the rip fence Model G0700 Mfg. since 8/09 Installing main blade Page Hose support installed Dust hoses attached Model G0700 Mfg. since 8/09 Power Connection To test run the saw Test RunOperation Overview OperationsNon-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsBlade Guard Riving Knife Riving Knife Installation & Removal Ripping Blade Features Blade Guard Installation & RemovalBlade Requirements Blade SelectionCombination blade features Crosscut blade features Laminate blade featuresDado Blades To change the main blade Changing Main BladeAdjusting Scoring Blade Changing/Adjusting Scoring BladeChanging Scoring Blade Rip Cutting with Sliding Table Rip CuttingRip Cutting with Rip Fence To perform a crosscutting operation CrosscuttingTo perform a miter cut Miter CuttingDado Cutting Installing Dado BladeDado Blade Cutting Dadoes with a Standard Blade Cutting Dadoes with a Dado BladeFinished Dado Cut To use a standard saw blade to cut dadoesCut 2 Blade Rabbet CuttingCutting Rabbets with a Standard Blade Cutting Rabbets with a Dado BladeBlade To cut rabbets with the standard bladeMaking Resaw Barrier ResawingTools Needed Qty Components Needed for Resaw BarrierComponents Needed for Resawing Resawing OperationsFeatherboards Shop Made Safety AccessoriesMaking a Featherboard Now, proceed to Mounting Featherboard in Miter Slot on Assembling miter slot featherboard ComponentsMounting Featherboard in Miter Slot Mounting Featherboards w/ClampsPush Sticks Using a Push StickMaking a Push Stick ⁄ 2 GridPush Blocks Using a Push BlockMaking a Push Block Zero-Clearance Insert Cutaway View Outfeed TableDrilled Hole Making a Narrow-Rip Push Block for an Auxiliary Fence Narrow-Rip Auxiliary Fence & Push BlockRipping with push block Model G0700 Mfg. since 8/09 Using the Auxiliary Fence and Push BlockBlades Aftermarket Accessories from GrizzlyT21382-Scoring Blade G7315Z-Super Heavy-Duty Shop FOX Mobile BaseH8003-Hydraulic Lifting lbs Eye protection assortmentCleaning MaintenanceSchedule Unpainted Cast IronLubrication Troubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalOperation Main Belt Replacement Belt ReplacementScoring Belt Replacement Stop Blade Tilt CalibrationTo adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentFence to Blade Squaring MiterTo square the miter fence with the blade To adjust the riving knife mount block Adjusting Riving Knife Mounting BlockWiring Safety Instructions Wiring220 VAC Wiring DiagramsElectrical Components Power junction box wiringParts Description Cabinet Parts ListHandwheels Main Motor Main Motor Parts List Blade Housing Tables Tables Parts List Fence Fence Parts List Miter Gauge Labels & Miscellaneous Model G0700 Mfg. since 8/09 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents