Grizzly G5959, G9957 instruction manual Safety Instructions For Power Tools

Page 4

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

 

 

 

 

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

WILL result in death or serious injury.

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COULD result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

 

 

 

 

against unsafe practices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE

 

This symbol is used to alert the user to useful information about

 

 

proper operation of the equipment.

 

 

 

 

 

 

 

 

 

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

-2-

G5959/G9957 12" Table Saw

Image 4
Contents HEAVY-DUTY 12 Table SAW Model G5959 and G9957G5959/G9957 12 Table Saw Table of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Safety Accessories Push Paddles Common Definitions, Terms and Phrases 220V Single-Phase 220V Three-Phase Circuit RequirementsWiring Diagram Grounding Extension CordsIntroduction CommentaryUnpacking Piece InventoryClean up Site ConsiderationsBeginning Assembly AssemblyExtension Wings Using tape to shim for wing alignment Fence RailsGuard Support Shaft Installing Saw BladeMotor Bracket Guard assembly square to table Blade Guard/SplitterAdjusted rear Table Insert Blade Height AdjustmentsBlade Tilt Miter Slot to Blade #1#3 #2#4 Miter Gauge Rip Fence SquareBlade Alignment Nylon PadsBlade Adjustment Cap Screw Arbor Bracket Pre-Run Check OperationsTest Run Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Crosscut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fenceRabbet cutting G5959/G9957 12 Table Saw Maintenance GeneralV-BeltTo adjust V-belt tension LubricationClosure Machine Data Sheet HP Magnetic Switch -NHD Type 2 HP Magnetic Switch -NHD Type 406 Page Page 45A 214 206 215 306 203A 307 202 204 207 Description Description Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G5959/G9957 12 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC