Grizzly G1023S110 instruction manual Saw Blade, Blade Guard/Splitter

Page 24

Saw Blade

To install a saw blade:

1.Disconnect the machine from the power source!

2.The arbor nut has left-hand threads. Loosen the arbor nut clockwise and remove the outside flange from the arbor. Remove and discard the 3Ú4'' diameter spacer on the arbor shaft.

Use caution and remain alert when working with the saw blade. Failure to follow this warning could result in serious personal injury or death.

3. Install the saw blade onto the arbor. Ensure that the blade teeth point toward you as you stand at the front of the saw.

4. Slide on the flange and thread the arbor nut back on.

5. Use the arbor wrench provided with the saw to tighten the arbor nut. Wedge a block of wood in the teeth of the blade to keep it from turning when tightening the nut as shown in

Figure 16.

!

Figure 16. Changing saw blade.

-22-

Blade Guard/Splitter

To install a blade guard/splitter:

1.Disconnect the machine from the power source!

2.Slip the blade guard/splitter over the mount- ing bolts as shown in Figure 17. The wash- ers should be between the bolt head and the slots. Tighten the bolts to secure the blade guard/splitter.

Blade Guard

Mounting Bolt

Anti-kickback Pawl

Figure 17. Blade guard and splitter in place.

3.Set a machinistÕs square against the face of the blade splitter. Slightly rotate the rear bracket to adjust the face of the blade splitter perpendicular to the table top as shown in

Figure 18.

!

Figure 18. Blade splitter square to table.

G1023S Series Heavy-Duty 10'' Table Saw

Page 23 Page 25
Image 24
Page 23 Page 25
Contents HEAVY-DUTY Table SAW Model G1023S & G1023S110Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryCircuit Requirements 110V Operation 220V OperationModel G1023S Only Grounding Extension Cord Machine Features Terms & DefinitionsMain Features SET UP Unpacking Piece InventoryG1023S Series component layout Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Extension Wings Switch To mount the switchDisconnect the machine from the power source Fence & Rails Cleanout Door Motor Brace Motor braceTo install the blade guard assembly Guard BracketHandwheel Table InsertSaw Blade Blade Guard/SplitterFront Support Blade Adjustment Bolt To adjust the miter gauge Miter GaugeRecommended adjustment checklist Start Up RecommendedStarting the machine Operations Blade SelectionPage Crosscutting Ripping Typical ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Rabbet cutting G1023S Series Heavy-Duty 10 Table SawRabbet cutting Maintenance GeneralLubricationTable BeltLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed Service Adjustments 45˚ & 90˚ StopsBlade Parallelism Page Blade Alignment Trunnion mounting boltsPage G1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Closure Overall Dimensions CapacitiesConstruction MotorPage Cabinet Complete Miter Gauge Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog
Top Page Image Contents