Grizzly G1023S110 instruction manual Blade Alignment, Trunnion mounting bolts

Page 44

Blade Alignment

The blade position can be adjusted slightly in case it contacts the table insert when raised or tilted. This adjustment can be made either by moving the whole trunnion assembly, or by just moving the arbor bracket. Try adjusting by mov- ing the whole trunnion first, this is the easier of the two ways.

To adjust the blade position by moving the trunnion:

1.Disconnect the machine from the power source!

2.Remove the table and wings and set them to one side. Be sure to note the position of the table shims. Replace them to their original position before re-attaching the table.

3.Loosen the four trunnion mounting bolts as shown in Figure 42, and nudge to either the left or right depending on where the blade is hitting the saw.

Trunnion Mount Bolts

Figure 42. Trunnion mounting bolts.

The table and wings rep- resent a very heavy load. DO NOT over- exert yourself while lift- ing or moving the table and wings – get assis- tance.

-42-

4.Reattach the table, making sure there is ade- quate blade clearance through all blade adjustments. Recheck guard alignment to the blade and to the table top. Adjust as nec- essary and tighten down all the bolts before use.

5.If the blade is still contacting the insert, repeat Steps 1-4. Check all other adjust- ments.

6.Recheck the blade to miter slot adjustments, and adjust as necessary.

Bracket Lock Bolt

Arbor Bracket

Figure 43. Adjusting arbor bracket.

To adjust the blade position by moving the arbor bracket:

1.Disconnect the machine from the power source!

2.Remove the table and wings and set them to one side. Be sure to note the position of the table shims. Replace them to their original position before re-attaching the table.

3.Loosen the bracket lock bolt shown in

Figure 43.

4.Slowly slide the arbor bracket towards the end of the shaft.

NOTICE

If you make the adjustment described in this section, check and adjust the blade splitter to make sure it aligns with the blade.

G1023S Series Heavy-Duty 10'' Table Saw

Image 44
Contents HEAVY-DUTY Table SAW Model G1023S & G1023S110Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryCircuit Requirements 110V Operation 220V OperationModel G1023S Only Grounding Extension Cord Machine Features Terms & DefinitionsMain Features SET UP Unpacking Piece InventoryG1023S Series component layout Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Extension Wings Switch To mount the switchDisconnect the machine from the power source Fence & RailsCleanout Door Motor Brace Motor braceTo install the blade guard assembly Guard BracketHandwheel Table InsertSaw Blade Blade Guard/SplitterFront Support Blade Adjustment Bolt To adjust the miter gauge Miter GaugeStarting the machine Recommended adjustment checklistStart Up Recommended Operations Blade SelectionPage Crosscutting Ripping Typical ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Rabbet cutting G1023S Series Heavy-Duty 10 Table SawRabbet cutting Maintenance GeneralLubricate the areas indicated below every 12 months LubricationTableBelt Belt deflection Date Approximate Hours Of Use Maintenance Performed Service Adjustments 45˚ & 90˚ StopsBlade Parallelism Page Blade Alignment Trunnion mounting boltsPage G1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Closure Overall Dimensions CapacitiesConstruction MotorPage Cabinet Complete Miter Gauge Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog