Grizzly G1023S110 instruction manual

Page 43

11.Refer to Figures 40 & 41, for shim place- ment. If the distance of A is shorter than B, shim(s) will need to be placed under corners #1 and #2. If the distance of B is shorter than A, shim(s) will need to be placed under cor- ners #3 and #4. Very thin shim stock works well, just make sure they are all the same thickness, and you put an equal number under each of the two corners.

12.Tighten down one bolt a small amount and then move on to each of the others, tighten- ing each down the same amount. Continue to rotate through the bolts, tightening them a little each time until they are all secure.

13.Now recheck the blade to miter slot at 90¡ and 45¡ by repeating Steps 1-5. If the dis- tance of A and B are equal, continue to the ÒMiter GaugeÓ instructions. If the distances are still off, repeat Steps 9-12.

14.Once you feel you have the miter slot adjust- ed to the blade, recheck all measurements and be sure the table mounting bolts are secure. Repeat Step 12 on Page 25. If the table is removed in the future, be sure to re- install the shims the same way they came off.

45û Bevel

!

 

#1 Shim

#4 Shim

#2 Shim

#3 Shim

Figure 40. 45¡ blade parallelism measurement.

45û Bevel

!

#1 Shim

#4 Shim

#2 Shim

#3 Shim

Figure 41. 45¡ blade parallelism measurement.

 

 

 

 

 

 

 

 

 

 

 

 

G1023S Series Heavy-Duty 10'' Table Saw

-41-

Image 43
Contents Model G1023S & G1023S110 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesPush Paddles Zero Clearance Table InsertsFeatherboards Commentary Introduction110V Operation 220V Operation Circuit RequirementsModel G1023S Only Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023S Series component layout Bolt Hardware Recognition ChartWorking Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Extension Wings Fence & Rails SwitchTo mount the switch Disconnect the machine from the power sourceMotor brace Cleanout Door Motor BraceGuard Bracket To install the blade guard assemblyTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeStart Up Recommended Recommended adjustment checklistStarting the machine Blade Selection OperationsPage Crosscutting Typical ripping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Rabbet cutting G1023S Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting General MaintenanceBelt LubricationTableLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Closure Motor Overall DimensionsCapacities ConstructionPage Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog