Grizzly G1023S110 instruction manual Additional Safety Instructions For Table Saws

Page 6

Additional Safety Instructions For Table Saws

1.THRU-SAWING:Use blade guard, splitter, and anti-kickback fingers on all thru-saw- ing operations. See Page 12 for the defin- ition of thru-sawing.

2.KICKBACK: Use anti-kickback devices during ALL cutting operations. If you do not have a complete understanding of how kickback occurs, or how to prevent it, Do not operate this table saw. See Page 12 for the definition of kickback.

3.DANGEROUS REACHING: Do not reach behind or over the saw blade with either hand while the saw is running.

4.PUSHSTICK: Use a push stick when rip- ping narrow stock.

5.FREE-HAND CUTTING: The fence or the miter gauge must support the workpiece during all cutting operations.

6.BODY POSITION WHEN CUTTING: Do not stand or have any part of your body in- line with the path of the saw blade.

7.WORKPIECE CONTROL: Hold the work- piece firmly against the miter gauge or fence and hold the workpiece firmly against the table.

8.CROSSCUTTING: Move the rip fence out of the way when crosscutting.

9.MITER GAUGE/RIP FENCE: Never use the miter gauge and rip fence at the same time.

10.STALLED BLADE: Never attempt to free a stalled saw blade without first turning the saw off.

11.CUTOFF TABLES: Use adequate support to the rear and sides of the saw table for wide or long workpieces.

12.HAND SAFETY: Avoid awkward cutting operations and hand positions where a sudden slip could cause your hand to move into the saw blade.

13.SAW BLADE: Lower the saw blade below the table when not in use.

14.DAMAGED SAW BLADE: Never use a damaged saw blade or one that has been dropped.

15.DADO CUTTING: There is a high degree of risk involved with any dado operation. See Page 12 for the definition of dado.

Unfamiliarity with this manual could result in serious personal injury. Become familiar with the contents of this manual, including all the safety warnings.

No list of safety guidelines can be com- plete. Operating this machinery may require additional safety precautions spe- cific to your shop environment. Failure to use reasonable caution while operating this machine could result in serious per- sonal injury.

-4-

G1023S Series Heavy-Duty 10'' Table Saw

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HEAVY-DUTY Table SAW Model G1023S & G1023S110Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryCircuit Requirements 110V Operation 220V OperationModel G1023S Only Grounding Extension Cord Machine Features Terms & DefinitionsMain Features SET UP Unpacking Piece InventoryG1023S Series component layout Hardware Recognition Chart BoltFloor Load Clean UpSite Considerations Working ClearanceBeginning Assembly Extension Wings Disconnect the machine from the power source SwitchTo mount the switch Fence & RailsCleanout Door Motor Brace Motor braceTo install the blade guard assembly Guard BracketHandwheel Table InsertSaw Blade Blade Guard/SplitterFront Support Blade Adjustment Bolt To adjust the miter gauge Miter GaugeRecommended adjustment checklist Start Up RecommendedStarting the machine Operations Blade SelectionPage Crosscutting Ripping Typical ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Rabbet cutting G1023S Series Heavy-Duty 10 Table SawRabbet cutting Maintenance GeneralLubricationTable BeltLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed Service Adjustments 45˚ & 90˚ StopsBlade Parallelism Page Blade Alignment Trunnion mounting boltsPage G1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Closure Construction Overall DimensionsCapacities MotorPage Cabinet Complete Miter Gauge Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog
Top Page Image Contents