Grizzly G0555X owner manual Dust Collection Blade Tracking, To connect a dust collection hose

Page 19

Dust Collection

Blade Tracking

 

 

 

 

 

 

Only operate the Model G0555X with an adequate dust collection system. This saw creates substantial amounts of fine wood dust while operating. Failure to use a dust collection system can result in respiratory illness.

Recommended CFM at Dust Port: 400 CFM

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must consider these variables: (1) CFM rating of the dust col- lector, (2) hose type and length between the dust collector and the machine, (3) number of branches or wyes, and (4) amount of other open lines throughout the system. Explaining how to calculate these variables is beyond the scope of this manual. Consult an expert or pur- chase a good dust collection "how-to" book.

To connect a dust collection hose:

1.Fit the 4" dust hose over the dust port, as shown in Figure 16, and secure in place with a hose clamp.

2.Tug the hose to make sure it does not come off.

Note: A tight fit is necessary for proper per- formance.

Figure 16. Dust hose attached to dust port.

G0555X 14" Extreme Series Bandsaw

"Blade Tracking" is how the blade rides on the wheels. When tracking correctly, the blade rides in the center of both wheels.

Blade tracking is primarily controlled by adjust- ing the upper wheel tilt. Tracking the blade in this manner is referred to as "Center Tracking," because you tilt the wheel until the blade rides in the center.

Another way to track the blade is known as "Coplanar Tracking." Coplanar tracking involves aligning the wheels so they are parallel and aligned. (See Wheel Alignment on Page 41.) When wheels are coplanar, the bandsaw decreas- es vibration and heat.

The wheels on the Model G0555X are factory aligned, so center tracking is the only adjustment that needs to be performed

To center track the blade:

1.DISCONNECT BANDSAW FROM POWER!

2.Adjust the upper/lower guide bearings and support bearings away from the blade.

3.Open the upper wheel cover.

4.Adjust the blade tension to match the size of the installed blade with the mark on the blade tension scale located on the back of the bandsaw.

5.Spin the upper wheel by hand at least three times and watch how the blade rides on the crown of the wheel. Refer to Figure 17 for an illustration of this concept.

—If the blade rides in the center of the upper wheel and is centered on the peak of the wheel crown, then the bandsaw is already tracked properly and no additional adjustments are needed. Skip to Step 9.

—If the blade does not ride in the center of the upper wheel and is not centered on the peak of the wheel crown, then continue with the next step.

-17-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements Circuit Requirements110V/220V Operation Amperage DrawGrounding Extension Cords Unpacking SET UPSet Up Safety Items Needed for SetupMain Components Figure Qty InventoryFasteners and Tools not shown Qty Hardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the bandsaw AssemblyExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw To connect a dust collection hose Dust Collection Blade TrackingTo center track the blade Changes in the blade tension may change the blade tracking Test RunTo tension the bandsaw blade Adjusting Support BearingsTo adjust the support bearings Tensioning BladeG0555X 14 Extreme Series Bandsaw To adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Adjusting Positive StopSetting Table Tilt Scale to 0˚ To set the positive stop 90˚ to the bladeTo level the extension table Leveling ExtensionRepeat Steps To align the fence parallel with the miter slot Aligning TableAligning Fence To align the miter slot parallel to the bandsaw bladeOperations Operation SafetyOverview Table Tilt Guide PostTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Typical resawing operation ResawingTo complete a stacked cut Cutting Curves Stacked CutsTooth Style Blade InformationBlade Length Blade WidthGrizzly Bandsaw Blades Tooth PitchBlade Care Blade BreakageTo remove the blade Blade ChangesTo replace the blade To calibrate the scale Scale CalibrationExtension Block Kit H3051 AccessoriesG1928-Bandsaw Handbook Lubricating MaintenanceCleaning ScheduleTroubleshooting ServiceMotor & Electrical Miscellaneous Cutting OperationsTo tension the belt Checking BeltTensioning Belt To check the beltTo replace the belt Replacing BeltTo shim the table Shimming Table Blade LeadTo skew your fence To verify if the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Coplanar diagram G0555X 14 Extreme Series BandsawBlade Tensioner To reset the blade tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Description Main Parts ListPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents