Grizzly G0555X owner manual Additional Safety Instructions for Bandsaws

Page 9

Additional Safety Instructions for Bandsaws

1.BLADE CONDITION. Do not operate with a dull, cracked, or badly worn blade. Dull blades require more effort to use and are difficult to control. Inspect blades for cracks and missing teeth before each use.

2.HAND PLACEMENT. Never position fin- gers or thumbs in line with the cut. Serious personal injury could occur.

3.GUARDS. Do not operate this bandsaw without the blade guard in place.

4.BLADE REPLACEMENT. When replacing blades, make sure teeth face toward the workpiece and the blade is properly ten- sioned before operating.

5.WORKPIECE HANDLING. Never hold small workpieces with your fingers when cutting. Always support/feed the workpiece with push stick, table support, vise, or some type of clamping fixture.

6.CUTTING TECHNIQUES. Plan your cuts so you always cut out of the wood. DO NOT back the workpiece away from the blade while the saw is running. If you need to back the work out, turn the bandsaw OFF and wait for the blade to come to a complete stop, and DO NOT twist or put excessive stress on the blade while back- ing work away.

7.BLADE SPEED. Allow blade to reach full speed before cutting.

8.LEAVING WORK AREA. Never leave a machine running while unattended. Allow the bandsaw to come to a complete stop before leaving unattended.

9.FEED RATE. Always feed stock evenly and smoothly. DO NOT force or twist blade while cutting, especially when sawing tight curves.

10.WORKPIECE MATERIAL. This machine is designed to cut wood only—it is not designed to cut metal.

11.MAINTENANCE/SERVICE. Do all inspec- tions, adjustments, and maintenance with the power OFF and the plug removed from the outlet. Wait for all moving parts to come to a complete stop.

12.BLADE CONTROL. Do not attempt to stop or slow the blade with your hand or a workpiece. Allow the blade to stop on its own.

13.EXPERIENCING DIFFICULTIES. If you experience difficulties performing the intend- ed operation, stop using the machine and contact our Technical Support Department at (570) 546-9663.

Like all machinery there is potential danger when operating this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the pos- sibility of operator injury. If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

G0555X 14" Extreme Series Bandsaw

-7-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws 110V/220V Operation Circuit RequirementsAmperage Draw Circuit RequirementsGrounding Extension Cords Set Up Safety SET UPItems Needed for Setup UnpackingInventory Main Components Figure QtyFasteners and Tools not shown Qty Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the bandsaw AssemblyExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw Dust Collection Blade Tracking To connect a dust collection hoseTo center track the blade Changes in the blade tension may change the blade tracking Test RunTo adjust the support bearings Adjusting Support BearingsTensioning Blade To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw To adjust the upper and lower blade guides Adjusting Blade GuidesSetting Table Tilt Scale to 0˚ Adjusting Positive StopTo set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleLeveling Extension To level the extension tableRepeat Steps Aligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotOperation Safety OperationsOverview Guide Post Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Typical resawing operation ResawingTo complete a stacked cut Cutting Curves Stacked CutsBlade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage Grizzly Bandsaw BladesBlade Changes To remove the bladeTo replace the blade To calibrate the scale Scale CalibrationAccessories Extension Block Kit H3051G1928-Bandsaw Handbook Cleaning MaintenanceSchedule LubricatingService TroubleshootingMotor & Electrical Miscellaneous Cutting OperationsTensioning Belt Checking BeltTo check the belt To tension the beltTo replace the belt Replacing BeltShimming Table Blade Lead To shim the tableTo skew your fence To verify if the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Coplanar diagram G0555X 14 Extreme Series BandsawBlade Tensioner To reset the blade tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Description Main Parts ListPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents