Grizzly G0555X owner manual Guide Post, Table Tilt, To tilt the table

Page 28

Motor & Light Switch

 

Guide Post

 

 

 

 

 

 

The motor switch is shown in Figure 27 and is clearly marked for starting/stopping the machine.

The light switch powers the lamp independently from the motor switch. ALWAYS turn this switch OFF (the "0" position) to cut power to the lamp BEFORE changing the light bulb.

Light Switch

Motor Switch

Figure 27. Motor & light switch.

Table Tilt

The bandsaw table tilts 10˚ left and 45˚ right to provide a wide range of cutting options.

To tilt the table:

1.Loosen the two table-trunnion knobs under- neath the table.

2.Tilt the table to the desired angle. (Refer to the angle gauge on the front table trunnion.)

3.Retighten both table-tunnion knobs.

NOTICE

When tilting the table to the left, it is necessary to remove the positive stop.

-26-

The guide post (shown in Figure 28) connects the upper blade guide assembly to the bandsaw. The guidepost allows the blade guide assembly to move up or down to be as close to the workpiece as possible. In order to cut accurately and safely, the bottom of the blade guide assembly must be no more than 1" from the workpiece at all times— this positioning provides the greatest support to the blade and minimizes operator exposure to the blade.

Guide Post

Lock Knob

Guide Post

Figure 28. Guide post controls.

To adjust the blade guide assembly on the guide post (the bandsaw must be turned OFF):

1.Make sure that the blade tension, blade tracking, support bearing and blade guides are adjusted correctly.

2.Loosen the guide post lock knob shown in Figure 28.

3.Raise/lower the guide post so the bottom of the blade guide assembly is less than 1" from the top of the workpiece.

4. Lock the guide post with the lock knob.

G0555X 14" Extreme Series Bandsaw

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 110V/220V OperationAmperage Draw Circuit RequirementsGrounding Extension Cords SET UP Set Up SafetyItems Needed for Setup UnpackingMain Components Figure Qty InventoryFasteners and Tools not shown Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the bandsawExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw To connect a dust collection hose Dust Collection Blade TrackingTo center track the blade Test Run Changes in the blade tension may change the blade trackingAdjusting Support Bearings To adjust the support bearingsTensioning Blade To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guidesAdjusting Positive Stop Setting Table Tilt Scale to 0˚To set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleTo level the extension table Leveling ExtensionRepeat Steps Aligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotOperations Operation SafetyOverview Table Tilt Guide PostTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Resawing Typical resawing operationCutting Curves Stacked Cuts To complete a stacked cutBlade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Grizzly Bandsaw BladesTo remove the blade Blade ChangesTo replace the blade Scale Calibration To calibrate the scaleExtension Block Kit H3051 AccessoriesG1928-Bandsaw Handbook Maintenance CleaningSchedule LubricatingTroubleshooting ServiceMotor & Electrical Cutting Operations MiscellaneousChecking Belt Tensioning BeltTo check the belt To tension the beltReplacing Belt To replace the beltTo shim the table Shimming Table Blade LeadTo skew your fence Wheel Alignment To verify if the upper and lower wheels are coplanarCoplanar diagram G0555X 14 Extreme Series Bandsaw Shimming a wheelTo reset the blade tensioner Blade Tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Main Parts List DescriptionPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents