Grizzly G0555X owner manual Adjusting Positive Stop, Setting Table Tilt Scale to 0˚

Page 24

NOTICE

The blade guides should only have light pressure against the blade.

9.Tighten the cap screws to lock the blade guides in position.

When the blade guide bearings are properly positioned, they rotate when the bandsaw wheel is turned and they can be rotated with your fingers when the blade is still.

NOTICE

Whenever changing a blade or adjusting ten- sion and tracking, the upper and lower blade guide bearings and guide-blocks must be re- adjusted before cutting operations.

Figure 25. Squaring table to blade.

6.Secure the plastic knobs and lock the positive stop bolt by tightening the hex nut against the casting. Ensure that the bolt does not turn by holding with another wrench while tightening the hex nut.

Adjusting Positive

Stop

An adjustable positive stop allows the table to easily return to 90˚ after tilting.

To set the positive stop 90˚ to the blade:

1.Make sure the blade is correctly tensioned as described in the Tensioning Blade instruc- tions on Page 19.

2.DISCONNECT BANDSAW FROM POWER!

3.Loosen the two plastic knobs that secure the table to the trunnions.

4.Loosen the hex nut that locks the positive stop bolt in place.

5.Raise the upper blade guide assembly and place a 6" machinist’s square or try-square on the table next to the side of the blade as illustrated in Figure 25. Adjust the positive stop bolt to raise or lower the table until the table is 90˚ to the blade.

Setting Table

Tilt Scale to 0˚

The pointer on the table tilt scale must be calibrat- ed in order for the scale reading to be accurate.

To calibrate the pointer on the table tilt scale:

1.Make sure that the blade is tensioned and is tracking correctly, and that the table is 90˚ to the blade (this procedure should be already completed with the Adjusting Positive Stop instructions).

2.Loosen the screw on the pointer so the point- er is able to move.

3.Align the tip of the pointer with the 0˚ mark on the table tilt scale.

4.Tighten the screw on the pointer so the point- er is locked in place.

-22-

G0555X 14" Extreme Series Bandsaw

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 110V/220V OperationAmperage Draw Circuit RequirementsGrounding Extension Cords SET UP Set Up SafetyItems Needed for Setup UnpackingInventory Main Components Figure QtyFasteners and Tools not shown Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the bandsawExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw Dust Collection Blade Tracking To connect a dust collection hoseTo center track the blade Test Run Changes in the blade tension may change the blade trackingAdjusting Support Bearings To adjust the support bearingsTensioning Blade To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guidesAdjusting Positive Stop Setting Table Tilt Scale to 0˚To set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleLeveling Extension To level the extension tableRepeat Steps Aligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotOperation Safety OperationsOverview Guide Post Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Typical resawing operationCutting Curves Stacked Cuts To complete a stacked cutBlade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Grizzly Bandsaw BladesBlade Changes To remove the bladeTo replace the blade Scale Calibration To calibrate the scaleAccessories Extension Block Kit H3051G1928-Bandsaw Handbook Maintenance CleaningSchedule LubricatingService TroubleshootingMotor & Electrical Cutting Operations MiscellaneousChecking Belt Tensioning BeltTo check the belt To tension the beltReplacing Belt To replace the beltShimming Table Blade Lead To shim the tableTo skew your fence Wheel Alignment To verify if the upper and lower wheels are coplanarCoplanar diagram G0555X 14 Extreme Series Bandsaw Shimming a wheelTo reset the blade tensioner Blade Tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Main Parts List DescriptionPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents