Grizzly G0555X owner manual Test Run, Changes in the blade tension may change the blade tracking

Page 20

Blade Centered

on Peak of Crown

Blade

Centered on Wheel

CENTER TRACKING

Figure 17. Center tracking profiles.

6.Loosen the lock nut on the blade tracking knob threads so the blade tracking knob will rotate for adjustments.

7.Spin the upper wheel with one hand and rotate the blade tracking knob with the other hand to make the blade ride in the center of the bandsaw wheel tire.

8.After the blade consistently rides in the center of the wheel, tighten the tracking control lock nut.

9.Close the upper wheel cover.

Note: For the best performance from your saw, regularly maintain the proper tracking of the blade.

NOTICE

Changes in the blade tension may change the blade tracking.

Test Run

Once the assembly is complete and you have performed the Blade Tracking steps on Page 17, you need to test run the machine to continue with the remainder of the adjustments.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop the machine immediately, then review Troubleshooting on Page 36.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

Wear safety glasses dur- ing the entire test run process. Failure to com- ply may result in serious personal injury.

To test run the machine:

1.Connect the machine to the power source.

2.Make sure that you have read the Safety section at the beginning of the manual and that the machine is setup properly.

3.Make sure all tools and objects used during set up are cleared away from the machine.

4.Turn the machine ON.

5.Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

—Strange or unusual noises must be inves- tigated and corrected before operating the machine further. Always disconnect the machine from power before investigating or correcting potential problems.

-18-

G0555X 14" Extreme Series Bandsaw

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 110V/220V OperationAmperage Draw Circuit RequirementsGrounding Extension Cords SET UP Set Up SafetyItems Needed for Setup UnpackingFasteners and Tools not shown Qty InventoryMain Components Figure Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the bandsawExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw To center track the blade Dust Collection Blade TrackingTo connect a dust collection hose Test Run Changes in the blade tension may change the blade trackingAdjusting Support Bearings To adjust the support bearingsTensioning Blade To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guidesAdjusting Positive Stop Setting Table Tilt Scale to 0˚To set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleRepeat Steps Leveling ExtensionTo level the extension table Aligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotOverview Operation SafetyOperations To tilt the table Guide PostTable Tilt To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Resawing Typical resawing operationCutting Curves Stacked Cuts To complete a stacked cutBlade Information Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Grizzly Bandsaw BladesTo replace the blade Blade ChangesTo remove the blade Scale Calibration To calibrate the scaleG1928-Bandsaw Handbook AccessoriesExtension Block Kit H3051 Maintenance CleaningSchedule LubricatingMotor & Electrical ServiceTroubleshooting Cutting Operations MiscellaneousChecking Belt Tensioning BeltTo check the belt To tension the beltReplacing Belt To replace the beltTo skew your fence Shimming Table Blade LeadTo shim the table Wheel Alignment To verify if the upper and lower wheels are coplanarCoplanar diagram G0555X 14 Extreme Series Bandsaw Shimming a wheelTo reset the blade tensioner Blade Tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Main Parts List DescriptionPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents