Grizzly G0555X Tensioning Blade, Adjusting Support Bearings, To tension the bandsaw blade

Page 21

Tensioning Blade

A properly tensioned blade is essential for mak- ing accurate cuts and is a prerequisite for making many bandsaw adjustments.

To tension the bandsaw blade:

1.Make sure that you have performed the Test Run instructions on the previous page and that the blade is tracking properly.

2.With the blade tension lever in the down (engaged) position, adjust the blade ten- sion so the mark on the blade tension scale matches the size of blade that is installed on the bandsaw.

Note: Because each blade is different and all blades stretch, this scale can only be consid- ered as a general guide.

3.Turn the bandsaw ON.

4.Release the tension one quarter of a turn at a time. Do this very slowly. When you see the bandsaw blade start to flutter, stop decreas- ing the tension.

5.Now, slowly increase the tension until the blade stops fluttering, then tighten the tension one more quarter of a turn.

6.Look at what the tension gauge reads and use that as a guide for tensioning that blade in the future.

Note: However, do not rely on this measure- ment for long periods of time because the blade will stretch with use.

NOTICE

To reduce blade stretching, remove the ten- sion from the blade when not in use.

NOTICE

After blade tension and tracking are set cor- rectly, properly adjust the upper/lower sup- port bearings and guide-block assemblies into position before cutting operations.

G0555X 14" Extreme Series Bandsaw

Adjusting Support

Bearings

The support bearings are positioned behind the blade and support the back of the blade dur- ing cutting operations. Proper adjustment of the support bearings is an important part of making accurate cuts and also keeps the blade teeth from coming in contact with the guide bearings while cutting.

To adjust the support bearings:

1.Make sure that the blade is tracking properly and that it is correctly tensioned.

2.DISCONNECT BANDSAW FROM POWER!

3.Familiarize yourself with the support bearing controls shown in Figure 18.

Lock Bolt

Knurled

Knob

Support

Bearing

Thumbscrew

Figure 18. Support bearing controls.

4.Loosen the lock bolt shown in Figure 18.

-19-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model G0555X Extreme Series Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws 110V/220V Operation Circuit RequirementsAmperage Draw Circuit RequirementsGrounding Extension Cords Set Up Safety SET UPItems Needed for Setup UnpackingInventory Main Components Figure QtyFasteners and Tools not shown Qty Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the bandsaw AssemblyExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw Dust Collection Blade Tracking To connect a dust collection hoseTo center track the blade Changes in the blade tension may change the blade tracking Test RunTo adjust the support bearings Adjusting Support BearingsTensioning Blade To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw To adjust the upper and lower blade guides Adjusting Blade GuidesSetting Table Tilt Scale to 0˚ Adjusting Positive StopTo set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleLeveling Extension To level the extension tableRepeat Steps Aligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotOperation Safety OperationsOverview Guide Post Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Typical resawing operation ResawingTo complete a stacked cut Cutting Curves Stacked CutsBlade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage Grizzly Bandsaw BladesBlade Changes To remove the bladeTo replace the blade To calibrate the scale Scale CalibrationAccessories Extension Block Kit H3051G1928-Bandsaw Handbook Cleaning MaintenanceSchedule LubricatingService TroubleshootingMotor & Electrical Miscellaneous Cutting OperationsTensioning Belt Checking BeltTo check the belt To tension the beltTo replace the belt Replacing BeltShimming Table Blade Lead To shim the tableTo skew your fence To verify if the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Coplanar diagram G0555X 14 Extreme Series BandsawBlade Tensioner To reset the blade tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Description Main Parts ListPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page

G0555X specifications

The Grizzly G0555X is a benchmark scroll saw that stands tall among woodworking enthusiasts and professionals alike. This versatile tool is designed to offer precision and efficiency when it comes to intricate cutting tasks, making it an essential addition to any woodshop.

One of the standout features of the G0555X is its robust 1 HP motor. This powerful motor allows for smooth and consistent operation, ensuring that users can tackle both intricate and heavy-duty cutting tasks efficiently. With variable speed control ranging from 400 to 1200 SPM (strokes per minute), users can adjust the speed according to the specific requirements of their projects, providing flexibility for different materials and designs.

The G0555X is built with a cast-iron frame, which enhances stability and reduces vibrations during operation. This heavy-duty construction not only ensures longevity but also improves precision in cutting. The saw's adjustable table, which can tilt from 0 to 45 degrees, allows users to make angled cuts with ease, offering versatility for various applications.

Another impressive characteristic of the G0555X is its exceptional blade deviation capabilities. The tool can accommodate both pinless and pinned blades, giving users the freedom to choose the best blade for their cutting needs. The saw features an easy blade installation and tensioning system, enabling quick and hassle-free blade changes, a feature that saves time and increases productivity.

In addition to performance, the G0555X emphasizes safety. The saw is equipped with a transparent blade guard that allows for clear visibility of the cutting area, ensuring that users can maintain focus on their work without compromising safety. The dust port also plays a crucial role in maintaining a clean workspace, accommodating a standard 4-inch hose for efficient dust collection.

With its impressive specifications and user-friendly design, the Grizzly G0555X is an excellent choice for both hobbyists and professionals. Whether you're tackling delicate wooden crafts or robust furniture projects, this scroll saw is engineered to deliver accuracy, power, and reliability. The G0555X exemplifies what modern woodworking tools should offer, combining advanced technology with essential features to elevate the woodworking experience. Its reputation among users speaks volumes, making it a go-to option for anyone serious about their craft.
Top Page Image Contents