6. SETTING AND ADJUSTMENTS BEFORE SHOOTING

6. SETTING AND ADJUSTMENTS BEFORE SHOOTING

6-3 Viewfinder Adjustment

 

2.

1.

 

 

Eyepiece

 

 

2. Eyepiece

1.

1.

focusing ring

 

 

 

 

3.

3.

 

CONT

BRIGHT

1. Adjust the position and angle of the viewfinder.

2. Diopter adjustment Rotate the eyepiece focusing ring until the viewfinder screen image is clearly visible.

3. Brightness and contrast adjustment When the ambient brightness changes, etc., the brightness and contrast of the viewfinder screen can be adjusted with the BRIGHT and CONT controls.

MEMO: The screen size of the viewfinder can be changed by selecting the desired size with the ASPECT RATIO item on the CAMERA OPERATION menu screen (4:3 or LETTER).

6-5 Back Focus Adjustment

3.

4. 6.

5.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RET

M

 

A

W T

1.

It is only necessary to perform this when the lens is attached for the first time or when focusing is not correct in both the telephoto and wide-angle positions.

It is easier to adjust back focus when the subject is more than 3 meters from the camera. The optimal subject for this adjustment is a Siemens star chart.

1. Set the IRIS mode switch to M (Manual).

2. Set the zoom mode to M (Manual).

3. Open the iris by turning the iris ring. If the illumination is too strong, reduce it or move to a darker place.

6-4 External Monitor Adjustment

MACRO

4. Turn the zoom lever until the lens is at the maximum telephoto position.

5. Bring the subject into focus.

PUSH

Color video monitor

1.

LINE OUT

Y/C OUT MONITOR OUT

3.~8.

2.

Display the camera built-in color bar signal on the video monitor and adjust the colors, contrast and brightness.

1. Connect a color video monitor to the MONITOR OUT connector of the GY-DV5000.

2. Set the COLOR BARS/CAMERA/AUTO KNEE switch to BARS to output the color bar signal (SMTPE type color bars).

3. Set the monitor’s BLUE CHECK function to ON while the color bars are being displayed so that the screen turns entirely blue and the color bars become blue stripes.

4. Adjust the CHROMA control of the monitor so that there is no difference in brightness between the color bars 1 and 8, 7 and D.

2.

7. 8. 10.

6. Set the lens to maximum wide-angle.

7. Loosen the back focus ring retaining knob.

8. View the same subject and adjust the back focus ring for the best possible focus.

9. Repeat steps 4. through 8. about three times for fine adjustment until the subject remains in focus in both the telephoto position and the wide-angle position.

10.Tighten the back focus ring retaining knob to secure the ring.

MEMO: ACCU FOCUS can also be used in the above step 3.

POWER VTR

ONOFF

SMTPE type color bars

White Yellow Cyan Green Magenta

Red

Blue

1

2

3

4

5

6

7

Blue

Black Magenta Black

Cyan

Black

White

8

9

0

A

B

C

D

Black

White

 

Black

 

 

 

E

F

 

G

 

HIJ K

5. With the BLUE CHECK function ON, adjust the PHASE control of the monitor so that there is no difference in brightness between the color bars 3 and 0, 5 and B.

6. If the phase control adjustment above causes a difference in brightness between the color bars 1 and 8, 7 and D, start again from the CHROMA control adjustment in step 4.

7. Set the monitor’s BLUE CHECK function to OFF to switch the monitor back to the standard screen (R, G and B will all appear).

8. Use the monitor's brightness control to adjust so that the color bars H and I disappear but J is visible.

EBU type colour bars

White

Yellow

Cyan

Green

Magenta

Red

Blue

Black

1

2

3

4

5

6

7

8

Siemens star chart

(U model)

(E model)

46

47

Page 25
Image 25
JVC GY-DV5000 instruction manual External Monitor Adjustment, Smtpe type color bars, EBU type colour bars