3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3-6 Attaching the Tripod Base (Provided)

4. POWER SUPPLY

The GY-DV5000 is operable with AC power supply or battery pack.

4-1 AC Operation

1.

Tripod mounting holes

3.

Pin

Front mount clip

Use the provided KA-550U tripod base to place the camera on a tripod.

1. Attach the tripod base on the tripod by using the hole that balances the unit most optimally.

2. While pushing the safety lever, pull the lock lever toward the front until the front mount clip clicks into place.

3. Place the unit on the tripod base by aligning the rear base mount of the unit with the pin on the tripod base.

Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.

Do not use any power source with large fluctuations in the

power source voltage, power sources generating noise,

such as ripples or power sources with lower voltage.

1. After making sure that the power switches of the GY-DV5000

2.

Safety lever

4. Front base mount

2.

Lock lever

3. Rear base mount

4.

4. Push the unit from the upward direction and slide it toward the front so that the front base mount of the unit is locked by the front mount clip of the tripod base as it clicks into place.

CAUTION:

The front base mount may be locked while the pin of the tripod base is not inserted into the hole on the rear base mount of the unit. Therefore, after mounting, make sure that these parts are engaged properly.

When moving the unit mounted on a tripod, any impact or vibration should be avoided as this may cause the unit to become detached and to drop from the tripod.

Be sure to remove the unit from the tripod before

transporting it.

AA-P250

and of the AA-P250 are set to OFF, connect the DC cable

from the AA-P250 to the DC IN connector of the GY-DV5000

 

 

as shown in the illustration.

DC cable

2. Set the CHARGE/CAMERA switch of the AA-P250 to

 

AC power adapter

CAMERA.

3. Press the POWER switch of the GY-DV5000 to ON. Power

 

 

is supplied to the VTR section and the camera.

 

* For details, read the instruction manual of the AA-P250.

 

MEMO:

 

Do not remove or connect the DC cable while recording is

 

being performed.

4-2 Battery Pack Operation (Optional)

The GY-DV5000 can be operated with the following battery packs.

 

Flat shape type battery pack

Anton-Bauer battery pack

 

*

An Anton-Bauer battery pack cannot be connected directly

Propack 13/14 Series

 

to the GY-DV5000. It is necessary to mount the optional

Trimpack 13/14 Series

 

battery holder.

 

Magnum 13/14 Series

 

Battery holder: Anton-Bauer QRQ27

 

Compack 13/14 Series

 

For details on how to mount the battery holder, see page

 

 

 

35.

When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power starts to be supplied through the DC IN connector.

Do not connect or disconnect the DC cable while operating with a battery pack.

The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.

The power is cut off for a moment when the DC cable is disconnected.

Noise to the video and audio signals occurs. Audio signal are muted.

When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF after the DC power is applied. Then switch ON again.

If the GY-DV5000 is left with the battery pack attached, a small amount of power is consumed even if the POWER

switch on the GY-DV5000 is set to OFF. Remove the battery pack when the GY-DV5000 is not going to be used.

32

33

Page 18
Image 18
JVC GY-DV5000 AC Operation, Battery Pack Operation Optional, Camera, Flat shape type battery pack Anton-Bauer battery pack