JVC GY-DV5000 instruction manual Right Side Section Cont’d

2. CONTROLS, INDICATORS AND CONNECTORS
2-2 Right Side Section (Cont’d)
	q	w	e
			y	u	r	t
					LCD BRIGHTDISPLAY
				AUDIO		PULL
				LEVEL	FRONT	OPEN
	EDITSEARCH
	MONITOR			CH-1CH-2	REAR
FILTER					CH-1	CH-2
3200K					AUDIO INPUT
5600K	/
5600K					AUDIO SELECT
5600K	/
SHUTTER STATUS					CH-1	CH-2
					AUTO
					MANUAL
MENU
		AUDIO
		LEVEL
	CH-1	CH-2
	POWER VTR			i		o

			2. CONTROLS, INDICATORS AND CONNECTORS
			View with cover open.
			!2 !0
				LCD BRIGHT	DISPLAY
			MONITOR
			SELECT		COUNTER		!3
			CH-1	FRONT
			MIX		TC
		EDITSEARCH	MONITOR	REAR	UB
			CH-2
3200K			CH-1 AUDIO CH-2	CH-1 CH-2
FILTER			LEVEL
5600K				AUDIO INPUT
5600K	/
5600K	/		AUDIO INPUT	AUDIO SELECT	TC GENE.		!4
			FRONT REAR	CH-1 CH-2
SHUTTER		STATUS	LINE	AUTO	REGEN	FREE
			MIC			REC
			+48V	MANUAL	PRST
MENU
			AUDIO
			LEVEL
			CH-1CH-2
	POWER VTR		!1
ON		OFF

ON OFF

0	[CH-1/CH-2 AUDIO INPUT] CH-1/CH-2 audio input
	selector switch
	This switch is used to select the input sound of the CH1 or

CAUTION: Make sure to move switches all the way. Do not leave a switch stopped in a midway position. Noise will be

1 Monitoring loudspeaker
	In the Camera mode, the input sound can be EE monitored. In
	the VTR mode, the speaker outputs the VTR playback sound.
	The sound to be output is selected with the MONITOR
	SELECT switch @.
	● The sound level is adjusted with the MONITOR sound
	level button 1 on page 12. The sound from this speaker
	is not output if an earphone is plugged into the PHONES
	jack 5 on page 18. This speaker also outputs various
	warning sounds superimposed on other sound. ☞ See
	“Alarm Sounds” on page 89.
2 LCD door
	LCD monitor door.
	The LCD monitor is located on the inner side of the door.
	The LCD monitor can be viewed when this door is opened.
	The door can be turned to change the orientation of the
	LCD monitor, and it can be rotated so that it can be
	accommodated in the main body of the camera.
	☞ See page 40.
3 LCD door lock and release knob
	To open the LCD door, move this knob in the direction toward
	the rear section.
4	[LCD BRIGHT +/–] LCD brightness +/– button
	This button is for adjusting the brightness of the LCD monitor
	display.
	● Pushing the button in the + direction makes the monitor brighter.
	● Pushing the button in the – direction makes the monitor darker.
	● Pushing the +/- buttons simultaneously returns the setting
	to the standard setting.
5	[DISPLAY] Display button
	This button is for turning the LCD monitor display ON/OFF
	and selecting the display mode.
	When this button is pressed for a long time, the LCD monitor
	display is turned ON or OFF.
	Each time this button is briefly pressed while the LCD
	monitor display is turned on, the display mode changes as
	shown in the following.
	Only image displayed → Characters shown enlarged
	↑
	Image and characters displayed ←

6	[CH-1 AUDIO LEVEL] CH1 audio level control
	Adjust the audio level of the CH1 audio channel with this
	control.
	● To use this control, set the CH1 AUDIO SELECT switch
	8 to “MANUAL”. This control works regardless of the
	setting of CH1 FRONT VR item on the AUDIO/VIDEO
	menu screen.
	To use this control, set the AUDIO LEVEL CH-1 control
	switch on the front section (7on page 10) to the maximum

(10)position, or set the CH1 FRONT VR item on the AUDIO/VIDEO menu screen to “DISABLE”.

7	[CH-2 AUDIO LEVEL] CH-2 audio level control
	Adjust the audio level of the CH2 audio channel with this
	control.
	● This control is valid only when the CH-2 AUDIO SELECT
	switch 9 is set to “MANUAL”.
8	[CH-1 AUDIO SELECT] CH-1 audio selector switch
	This switch is used to select the method for adjusting the
	audio level of the CH-1 audio channel.
	AUTO	:	The audio level is held at the reference level
			even when sounds greater than the reference
			level are input.
			The audio level does not increase when the
			input level is low.
	MANUAL :		The audio level can be adjusted with the CH-1
			AUDIO LEVEL control 6or the AUDIO LEVEL
			CH-1 control 7 on page 10.
			To use the AUDIO LEVEL CH-1 control on the
			front section, the CH1 FRONT VR item on the
			AUDIO/VIDEO menu screen should be set to
			“ENABLE”.
9	[CH-2 AUDIO SELECT] CH-2 audio selector switch
	This switch is used to select the method for adjusting the
	audio level of the CH-2 audio channel.
	AUTO	:	The audio level is held at the reference level
			even when sounds greater than the reference
			level are input.
			The audio level does not increase when the
			input level is low.
	MANUAL :		The audio level can be adjusted with the CH-2
			AUDIO LEVEL control 7.

CH2 audio channel. It is selected for each of the CH1 and
CH2 channels.
FRONT	: The sound from the FRONT AUDIO IN connector
REAR	on the front side section is input.
	: The sound from the REAR AUDIO IN connector
	on the rear side section is input.

! [FRONT/REAR AUDIO INPUT] Front/rear audio
input signal selector switch.
This switch is used to select the input sound signal from
the FRONT AUDIO IN connector and the REAR AUDIO IN
connector.
LINE	: Set to this position when connected to audio
	equipment, etc. The reference input level is +4 dBs.
MIC	: Set to this position when the microphone is
	connected. The reference input level is -60 dBs.
+48V	: Set to this position when a microphone requiring
	+48 V power supply (phantom microphone, etc.) is
	connected. This connector supplies +48 V DC
	current.
	When using the provided microphone connected
	to the FRONT AUDIO IN connector, set the FRONT
	AUDIO INPUT switch to this setting.
CAUTION:
When connecting a component that does not require
+48 V power supply, make sure that the switch is not
set to +48V before the component is connected.
@ [MONITOR SELECT] Audio monitor selector switch
This switch is used to select the monitor sound output and
playback sound output from the monitoring loudspeaker 1
or the PHONES 5 jack on page 18.
CH-1	: The CH1 channel audio is output.
MIX	: CH1 and CH2 channel audio are output mixed.
	When this setting is selected, the menu screen can
	be used to select whether the mixed sound or stereo
	sound should be output via the PHONES jack.
	(AUDIO MONITOR item on the AUDIO/VIDEO
	menu screen)
	When AUDIO MONITOR in the AUDIO/VIDEO
	menu screen is set to “STEREO”, only the audio of
	CH-1 is output from the monitoring loudspeaker.
CH-2	: The CH2 channel audio is output.

☞See “Outputting CH-3, CH-4 Channel Audio” on page 59.

☞See “AUDIO/VIDEO Menu Screen” on page 72.

generated and operation irregularities will occur.

# [COUNTER] Counter display switch
Selects the contents displayed on the TC counter of the
LCD monitor or in the viewfinder. (This switch works when
the TC/UB item on the LCD/VF (2/2) menu screen is set to
ON.)
TC :	Set to this position to display time code values.
UB :	Set to this position to display the user’s bits values.

$	[TC GENE.] Time code generator setting switch
	Switch for setting the time code generator to preset mode
	or regeneration mode. It is also used to select the time code
	run mode when the preset mode is selected.
	PRST-FREE : The preset mode is selected, and the time
		code run mode becomes the FREE run
		mode.
		Set to this position to record with the time
		code or user’s bits set anew (preset). In this
		setting, the time code always operates in the
		run mode.
	* If this setting is used when recording scenes one after
	another, the time codes become discontinuous at the
	transition points between scenes.
	PRST-REC	: The preset mode is selected, and the time
		code run mode becomes the REC run mode.
		Set to this position to record with the time
		code or user’s bits set anew (preset). The
		time code operates in the run mode during
		recording only. If this setting is used when
		recording scenes one after another, the time
		codes are recorded as continuous time
		codes.
	REGEN	: Regeneration mode, in which the unit reads
		existing time codes on the tape and records
		time codes in continuation of the existing
		ones. Set to this position when you want to
		add additional time codes to time codes
		already recorded on the tape.

MEMO: Preset of time code and user’s bits is performed on the TC/UB/CLOCK menu.

☞See “TIME CODE OPERATION” on page 62.

☞See “TC/UB/CLOCK Menu Screen” on page 75.

14 15