Global Machinery Company LS8B instruction manual Safety instructions, Laser Light Laser Radiation

Page 4

LASER LIGHT

LASER RADIATION

Do not stare into beam. Only turn laser beam on when tool is on work piece. Class 1 laser product.

Never aim the beam at any person or an object other than the work piece.

The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person for longer than 0.25s.

Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces. I.e. wood or rough coated surfaces are acceptable. Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator.

Do not change the laser light assembly with a different type. Repairs must only be carried out by the laser manufacturer or an authorised agent.

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Please refer to the relevant Australian standards, AS 2397 and AS/NZS2211 for more information on Lasers.

Safety instructions

The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse.

To use this tool properly, you must observe the safety regulations, the assembly instructions and the operating instructions to be found in this Manual. All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards. Children and infirm people must not use this tool. Children should be supervised at all times if they are

in the area in which the tool is being used. It is also imperative that you observe the accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety.

The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes.

Warning. When using power tools, basic safety precautions should always be taken to reduce the risk of fire, electric shock and personal injury. Also, please read and heed the advice given in the additional important safety instructions.

1.Keep the work area clean and tidy. Cluttered work areas and benches invite accidents and injury.

2.Consider the environment in which you are working. Do not use power tools in damp or wet locations. Keep the work area well lit. Do not expose power tools to rain. Do not use power tools in the presence of flammable liquids or gases.

3.Keep visitors away from the work area. All visitors and onlookers, especially children and infirm persons, should be kept well away from where you are working. Do not let others in the vicinity make contact with the tool or extension cord.

4.Store tools safely. When not in use, tools should be locked up out of reach.

5.Do not force the tool. The tool will do the job better and safer working at the rate for which it was designed.

6.Use the correct tool for the job. Do not force small tools or attachments to do the job best handled by a heavier duty tool. Never use a tool for a purpose for which it was not intended.

7.Dress correctly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-slip footwear are recommended when working outdoors. If you have long hair, wear a protective hair covering.

4

Image 4
Contents Redeye Contents Specifications Safety rules for laser lightsSafety instructions Laser Light Laser RadiationAdditional safety rules for band saws Unpacking AccessoriesSupport the work properly Know your product Saw bladeAssembly Upper blade guide adjustmentMounting Workpiece maximum distance 3mmLower blade guide adjustment Press the guide pins together against the band saw bladeTighten the thrust bearing locking screw Tighten the guide pin locking screwsHousing doors Adjusting the rip fenceUpper housing door Touch the saw bladeAdjusting the saw blade tension Adjusting the bevel angleAdjusting the blade tracking Installing and removing band saw blades Tighten the table locking knob 20 and table setting leverDust collector connection Turning on and offOpen both housing doors If required, adjust the saw blade trackingOperation Remove the rip fence 13 from the tableChanging the batteries Using the Redeye laser line generatorDo not mix old and new batteries Maintenance Power cord maintenanceSave this Manual for future reference