Emerson 400508-02 Safety Considerations, Safety Precautions, Enclosure, Safety of Machinery

Page 9

Safety Considerations

Safety Precautions

This product is intended for professional integration into a complete system. If you install the product incorrectly, it may present a safety hazard. The product and system may use high voltages and currents, carry a high level of stored electrical energy, or control mechanical equipment that can cause injury.

You should give close attention to the electrical installation and system design to avoid hazards either in normal operation or in the event of equipment malfunction. System design, installation, commissioning and maintenance must be carried out by personnel who have the necessary training and experience. Read and follow this safety information and the instruction manual carefully.

Enclosure

This product is intended to be mounted in an enclosure which prevents access except by trained and authorized personnel, and which prevents the ingress of contamination. This product is designed for use in an environment classified as pollution degree 2 in accordance with IEC664-1. This means that only dry, non-conducting contamination is acceptable.

Setup, Commissioning and Maintenance

It is essential that you give careful consideration to changes to drive settings. Depending on the application, a change could have an impact on safety. You must take appropriate precautions against inadvertent changes or tampering. Restoring default parameters in certain applications may cause unpredictable or hazardous operation.

Safety of Machinery

Within the European Union all machinery with which this product is used must comply with Directive 89/392/EEC, Safety of Machinery.

The product has been designed and tested to a high standard, and failures are very unlikely. However the level of integrity offered by the product’s control function – for example stop/ start, forward/reverse and maximum speed – is not sufficient for use in safety-critical applications without additional independent channels of protection. All applications where malfunction could cause injury or loss of life must be subject to a risk assessment, and further protection provided where needed.

Warning

General warning

Failure to follow safe installation guidelines can cause death or serious injury. The voltages used in this unit can cause severe electric shock and/or burns, and could be lethal. Extreme care is necessary at all times when working with or adjacent to this equipment. The installation must comply with all

vii

Image 9
Contents FM-3 Programming Module Installation Manual Page FM-3 Programming Module Installation Manual Page Customer Service Service Support 952995-8033952995-8011 Application Engineering 800893-2321 Sales 952995-8000 Training Services Or FaxRepresents Document ConventionsReference Materials Safety InstructionsGeneral Warning Qualified PersonSafety Precautions Safety ConsiderationsSetup, Commissioning and Maintenance Safety of MachineryViii Table of Contents Page Series EN Drive with FM-3 Function Module IntroductionFM-3 Programming Module Installation Manual Installation Basic Installation NotesMechanical Installation Grip the FM On each side LCD Modbus CommunicationsPC System Configuration Software InstallationPreparing for PowerTools FM-3 Installation Installing PowerTools FM-3Starting the Software Starting and Exiting PowerToolsAccessing Help To display Help in PowerTools, do one of the followingExiting the Software FM-3 Programming Module Installation Manual Diagnostic Display Diagnostics and TroubleshootingFault Codes Diagnostics and Troubleshooting Fault Descriptions Power Module Invalid ConfigurationHigh DC Bus Low DC BusMax Following Error RMS Shunt PowerEncoder Hardware Motor OvertempFM-3 Specific Fault Descriptions Brake Release Brake OperationAnalog Outputs Default Analog Output SourceAnalog Output Offset units Analog Output Scale unitsDiagnostic Output Test Points Diagnostic Analog Output Test PointsDiagnostic Cable Dgne Diagram Error Messages Drive FaultsResetting Faults Viewing Active Drive FaultsError The maximum limit of Instances is reached Non-Programming Error MessagesError Your Application is not valid to download Programming Error MessagesError a FM3 number’s mantissa must be between -2147483647 FYI Your Application hasError Couldnt find named Variable Error Can only compare,,etc numeric resultsError Couldnt find named Variable from Text Error Program Instance does not ExistError Text Strings are limited to 12 characters Error Syntax error encounteredError The destination variable does not accept Data Error The destination variable is Read OnlyDiagnostics and Troubleshooting Error This is not a fully qualified variable Error This instance does not existError This variable cannot be assigned a selection value Error This variable type cannot be assigned a valueOnline Status Indicators Global Where Am I ButtonMotion Status FM-3 Programming Module Installation Manual Dimensions and Clearances Specifications66.0 Specifications Cable DiagramsSNCDD-001.5 Cable SNCE-XXX CableSNCO-003 Cable SNCI-003 Cable SNCLI-003 Cable CMDX-XXX Cable CMDO-XXX Cable CDRO-XXX Cable TIA-XXX Cable DDS-XXX Cable TERM-H Head Terminator TERM-T Tail Terminator CMDS-XXX Cable CMMS-XXX Cable CFCS-XXX Cable CFCO-XXX Cable CFOS-XXX Cable Vendor Contact Information Index SymbolsFM-3 Programming Module Installation Manual

400508-02 specifications

The Emerson 400508-02 is a pivotal component in the realm of industrial automation and process control. It is designed to provide precise control and exceptional performance, meeting the demands of various industries, including oil and gas, food and beverage, and pharmaceuticals. This intelligent device is renowned for its reliability, accuracy, and user-friendly features.

One of the main features of the Emerson 400508-02 is its advanced connectivity options. The device is equipped with various communication protocols, such as HART, PROFIBUS, and Modbus, enabling seamless integration into existing systems. This flexibility allows operators to easily monitor and control processes in real-time, enhancing operational efficiency and reducing downtime.

The Emerson 400508-02 utilizes state-of-the-art sensor technologies that offer high accuracy and responsiveness. This results in improved measurement precision and faster response times, which are critical in ensuring optimal process control. The device is designed to handle a wide range of process conditions, making it suitable for diverse applications. Its robust design ensures that it can withstand harsh environments, including extreme temperatures and pressures.

Another notable characteristic of the Emerson 400508-02 is its intuitive user interface. The device typically features a digital display along with straightforward controls, allowing for easy configuration and troubleshooting. This user-friendly design minimizes the learning curve for operators and enhances overall productivity.

Additionally, the Emerson 400508-02 is built with advanced diagnostics capabilities. This system can monitor its own performance and send alerts for potential issues, enabling proactive maintenance strategies. By identifying problems before they lead to breakdowns, facilities can reduce maintenance costs and enhance operational uptime.

Incorporating Emerson’s commitment to sustainability, the 400508-02 is energy-efficient, helping businesses reduce their carbon footprint while maximizing process efficiency. With a focus on digital transformation, this device aligns with industry trends, incorporating IoT technologies that facilitate data collection and analysis for better decision-making.

In conclusion, the Emerson 400508-02 stands out in the industrial automation landscape due to its advanced features, connectivity options, robust design, and user-friendly interface. Its integration of cutting-edge technologies ensures that it meets the challenging demands of modern industrial environments, making it an essential tool for process optimization and efficiency.