Woodstock W1815 manual Service, General, Table Gap & Parallelism, Tools Needed

Page 24

Model W1815 (Mfg. Since 10/10)

SERVICE

General

SERVICE

This section covers the most common service adjustments or procedures that may need to be made during the life of your machine.

If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.

Table Gap & Parallelism

The miter slot must be parallel with the face of the sanding disc and there should be a 3⁄16" gap between the edge of the table and sanding disc. This gap should be large enough so that the sandpaper does not rub against the table, but small enough so that the gap is not a pinch hazard.

Tools Needed:

 

Wrench 10mm

1

Ruler

1

To set the table gap and parallelism, do these steps:

 

1.DISCONNECT MACHINE FROM POWER!

2.Loosen the six hex bolts that secure the table to the table support brackets.

3.Adjust the table so that there is a 3⁄16'' gap (Figure 17) between the disc (with sandpaper installed) and the edge of the table along its full length.

4.When the miter slot is parallel with the sanding disc, tighten the hex bolts.

5.Spin the disc by hand to check if the sandpaper touches the table.

IMPORTANT: DO NOT turn the disc sander ON at this point.

—If the if the sandpaper touches the table at any point in its rotation, re-adjust the table parallelism.

Make sure that your machine is unplugged during all service proce- dures! If this warning is ignored, seri- ous personal injury may occur.

*Ð(-

KfgM`\n

 

 

JXe[`e^;`jZ

 

KXYc\

Figure 17. Table parallel with sanding

disc.

-22-

Page 23 Page 25
Image 24
Page 23 Page 25
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportMachine Description B68=C HE886IDCH Model W1815 Mfg. Since 10/10 Controls and Features IdentificationSAFETYJ8=KP ZXlj\XdX\kfk\dXZ`e\ip%Safety Additional Safety for Disc Sanders 220V/240V, 60 Hz, Single-Phase ElectricalCircuit Requirements AmpsGrounding Requirements Extension CordsSetup UnpackingInventory Main Inventory Figure QtyMachine Placement Weight LoadCleaning Machine To remove the rust preventative coating, do these stepsAssembly To assemble the cabinet and mount the sander, do these stepsSander installation Test Run To test run the machineOperations Operation OverviewAttaching Sandpaper To attach sandpaper, do these stepsDisc Sanding To use the sanding disc, do these stepsAccessories Maintenance CleaningSchedule LubricationService GeneralTable Gap & Parallelism Tools NeededMiter Gauge Calibration To calibrate the miter gauge, do these stepsTable Tilt Calibration To calibrate the table tilt, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram StopTroubleshooting Problem Possible CauseInstall a coarse grit sandpaper, or strip coating off Parts MainMachine Labels DescriptionModel W1815 Mfg. Since 10/10 Place Stamp Here Warranty =\FjVainBVXcZhVcYIddah

W1815 specifications

The Woodstock W1815 represents a unique blend of traditional craftsmanship and modern technology, making it a standout watch in the realm of timepieces. Renowned for its elegant design and meticulous engineering, the W1815 caters to both watch enthusiasts and those seeking a reliable daily wear.

The Woodstock W1815 features a classic round case made from high-grade stainless steel, which not only ensures durability but also gives it a timeless aesthetic appeal. The polished finish reflects light beautifully, enhancing its overall visual impact. The watch is offered in various sizes, allowing for a range of preferences when it comes to wrist fit.

One of the most notable characteristics of the W1815 is its striking dial. Available in multiple colors, it combines functionality with elegance. The watch boasts luminescent hour markers and hands, ensuring readability in low light conditions. A date display is subtly integrated into the design, adding practicality without compromising the watch's sophistication.

At the heart of the W1815 is a reliable quartz movement. This technology provides accurate timekeeping with minimal maintenance. Unlike traditional mechanical watches, the quartz movement allows for thinner casing, contributing to the watch’s sleek profile. Additionally, the battery life of the W1815 is impressive, lasting several years before needing replacement, making it ideal for individuals who prefer low-maintenance timepieces.

Another standout feature of the Woodstock W1815 is its water resistance. Built to withstand the rigors of daily life, it is rated for water exposure up to a certain depth, allowing wearers to wear it confidently during various activities, whether it’s swimming, showering, or simply washing hands.

The strap options available for the W1815 further enhance its versatility. From premium leather to stainless steel bracelets, each option is designed to provide comfort and style. The quick-release mechanism makes changing straps an effortless task, allowing users to customize their watch according to personal style or occasion.

In summary, the Woodstock W1815 encapsulates a harmonious fusion of style, functionality, and durability. Its combination of advanced quartz movement, thoughtful design features, and various customization options make it an appealing choice for anyone in search of a reliable and fashionable timepiece. Whether for formal events or everyday wear, the W1815 stands as a testament to Woodstock's commitment to quality and innovation in horology.
Top Page Image Contents