Woodstock W1737, W1738 owner manual Pressure Rollers, Belt and pressure roller Adjustments

Page 35

W1737/W1738 Owner's Manual (Mfg. 10/09+)

Pressure Rollers

The pressure rollers are factory set so they are parallel with each other, parallel with the sanding drum, and parallel with the surface of the conveyor table.

Additionally, the front pressure rollers must be set 0.040" below the sanding drum, and the rear rollers set at 0.020" below the sanding drum. When these settings are achieved, the pressure-roller spring tension will be correct.

To adjust the pressure rollers, do these steps:

1.TURN OFF and LOCK the master power switch so no power can go to your sander!

2.Make two gauge boards that are 37" long and uniform in thickness.

3.Connect the air pressure and set it to 70 PSI.

4.Install the sanding belt and turn the belt tensioning knob to the 12:00 position to tension the belt. See

Figure 51.

5.Position each board on each side of the conveyor belt and directly below the front and back pressure rollers. See Figure 52.

6.Loosen the adjustment jam nuts and raise the pressure rollers above the sanding belt roller with the adjustment bolts shown in Figure 51.

7.Raise the table up until the boards barely touch the sanding belt.

8.Turn the table-height handwheel counterclockwise one complete turn, to lower the table approximately 0.020".

9.Lower the rear pressure rollers so that both ends barely touch the gauge boards. The rear pressure rollers are now set at 0.020" below the sanding drum.

10.Turn the table-height handwheel counterclockwise again one complete turn, which lowers the table an additional 0.020".

11.Lower the front pressure rollers so that both ends just touch the boards. The front pressure rollers are now set at 0.040" below the sanding drum.

12.Tighten the adjustment jam nuts.

Belt

Tension

Knob

Pressure

Roller Tension

Adjustor Bolt

and Jam Nut

Figure 51. Belt and pressure roller

adjustments.

Figure 52. Gauge boards placed under

pressure rollers.

SERVICE

-33-

Image 35
Contents OWNERS MANUAL Grinding, drilling, and other construction activities Contents Service Woodstock Technical Support About Your New SanderIndependent Motor Control System Specifications W1737 and W1738Controls and Features W1737/W1738 Disconnect machine when cleaning, adjusting or servicing Standard Safety InstructionsKeep stable footing and balance at all times Additional Safety Instructions for Sanders Correct body and hand positioning Avoiding Potential Injuries220V/440V Operation Phase Converter Connection440V Conversion W1738 Disconnect the sander from the power sourceUnpacking Box ContentsCleaning Machine Machine PlacementSanding Belt Installation Air Hose InstallationDust Collection Breather PinSanding Load Amp Meter Control PanelTo complete the test run, do these steps General OperationTest Run To change the feed belt speed do these steps Setting Feed SpeedUsing the Amp Draw Meter Selecting SandpaperTo use the emergency stop, do these steps Emergency StopKeypad and Display Calibrating the TableTo sand a workpiece, do these steps Basic SandingTip Complete Belt Tracking on Using the PlatenJet Air Flow Belt Tracking Belt tracking adjustmentOscillation system Belt Oscillation SpeedLubrication GeneralMaintaining Air System Cleaning BeltsTo adjust table stop switches, do these steps Table Stop SwitchesRelieve the air pressure Brake ServiceTo check the condition of the brake pads, do these steps Changing V-Belts Remove the upper belt adjustment nut and washerBelt Tension Sanding motor V-belt Adjustment Tension NutTable Parallelism To adjust the table parallelism, do these stepsFeed Belt Tension Tracking To adjust the feed belt tension and tracking, do these stepsBelt Tension Safety Switch Belt Tracking Safety SwitchPressure Rollers Belt and pressure roller AdjustmentsGeneral Motor and Transformer Connection W1737 220V Single-Phase Motor ConnectionW1737 and W1738 Control Panel Wiring W1737 General Wiring Diagram Connects To The T Terminal Only W1738 General Wiring DiagramW1738 Electrical Box Component Locations Box Wiring Diagram W1737 Electrical Box Component Locations W1737 Electrical Electrical Parts W1738 440V Conversion Parts Tools and Cabinet Parts Sandpaper #180 Sanding Motor and Frame Parts Machine Frame Table Lift System Parts Electrical BOX W1738 Feed System and Conveyor Parts XPB16 Upper Roller System Parts Eccentric ROD Air System Parts Connector 1/4N X 1/8T Sanding Drum and Roller Parts PART
# Description Safety Label Placement Description Parts Symptom Possible Cause How To Remedy TroubleshootingWarranty Comments Warranty RegistrationWoodstock international, inc. p.o. box Bellingham, wa Page High Quality Machines and Tools
Related manuals
Manual 68 pages 54.5 Kb

W1737, W1738 specifications

Woodstock W1738 is a cutting-edge digital audio workstation (DAW) designed for musicians, producers, and sound engineers seeking a versatile platform for music production. This innovative software solutions suite combines user-friendly interfaces with powerful features and state-of-the-art technologies to create an exceptional audio experience.

At its core, the Woodstock W1738 prioritizes ease of use while maintaining high functionality. The intuitive layout accommodates users of all skill levels, from beginners to seasoned professionals. The main workspace is organized in a way that promotes efficiency, allowing users to access crucial tools and features easily. The software supports various audio formats, ensuring compatibility with a wide range of audio files and devices.

One of the standout features of the Woodstock W1738 is its advanced virtual instrument library. Offering a rich selection of synthesized sounds, acoustic instruments, and samples, it caters to various genres and styles. Users can easily integrate these instruments into their compositions, enhancing creativity and inspiration. Additionally, the library includes customizable effects that allow artists to shape their sounds uniquely.

The W1738 sets itself apart with its real-time collaboration capabilities. Musicians from different locations can work together seamlessly, sharing tracks, edits, and ideas instantly. This feature broadens the creative possibilities, enabling artists to collaborate in ways previously inconceivable.

In terms of audio editing, the Woodstock W1738 boasts powerful tools that include pitch correction, time stretching, and audio restoration. These technologies allow users to manipulate sound with precision, ensuring that every note and beat aligns perfectly with their vision. The software also includes a robust mixer with multitrack recording functionalities that make it easy to handle complex projects.

Furthermore, the integration of artificial intelligence features within the W1738 enhances user experience by providing automatic mixing suggestions, mastering presets, and intelligent sound analysis. These AI capabilities not only streamline the production process but also inspire users to explore new creative avenues.

The Woodstock W1738 embodies a commitment to high-quality audio resolution, supporting up to 32-bit/192 kHz audio fidelity. This ensures that the end result is nothing short of professional-grade quality, suitable for commercial release or personal enjoyment.

Overall, the Woodstock W1738 serves as a dynamic platform for audio production that combines innovative technology, ease of use, and collaborative features, making it an essential tool for modern musicians and producers seeking to express their creativity.