Woodstock M1113 owner manual 220V Operation, Extension Cords, Electrical Specifications

Page 11

M1113 18" Wood/Metal Bandsaw

ELECTRICAL

The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Test Run" portion of this manual.

220V Operation

The Model M1113 operates on 220V single-phase power. We recommend connecting this machine to a dedicated circuit with a verified ground, using the circuit size given below. Never replace a circuit breaker with one of higher amperage without consulting a qualified electrician to ensure compliance with wiring codes. This machine must be connected to a grounded circuit!

A plug is not supplied with this machine. See below for the recommended plug type for this machine.

If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared cir- cuit, you may create a fire or circuit overload hazard— consult a qualified electrician to reduce this risk.

Extension Cords

We do not recommend using an extension cord; however, if you have no alternative, use the following guidelines:

•Use a cord rated for Standard Service (S).

•Do not use an extension cord longer than 50 feet.

•Ensure that the cord has a ground wire and pin.

•Use the gauge size listed below as a minimum.

Electrical Specifications

6-15P6-15R

Figure 1. 6-15 plug and receptacle.

DO NOT work on your electrical system if you are unsure about electrical codes and wiring! Seek assistance from a qualified electrician. Ignoring this warning can cause electrocution, fire, or machine damage.

ELECTRICAL

Operating Voltage	Amp Draw	Min. Circuit Size	Recommended Plug	Extension Cord
220V Single-Phase	5 Amps	15A	NEMA 6-15 (not incl.)	14 Gauge

-9-

Image 11

Contents WOOD/METAL Bandsaw Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Extension Cords Electrical SpecificationsElectrical 220V OperationMain Components Figure Qty SetupInventory Cleaning Machine Machine PlacementTo lift and move the bandsaw with a forklift, do these steps Lifting & MovingBolting to Concrete Floors Mounting to Shop FloorTo assemble the bandsaw, do these steps AssemblyInstalling fence onto rails Recommended CFM at each Dust Port Dust CollectionTo center track the blade Blade TrackingTo test run the machine, do these steps Test RunTo tension the bandsaw blade Blade TensioningSupport Bearing AdjustmentTo adjust the support bearings, do these steps To adjust the upper and lower blade guides, do these steps Blade Guide AdjustmentTable Tilt Scale Calibration Table Stop AdjustmentFence Alignment Table AlignmentBasic Controls OperationsGeneral Choosing wood without embedded foreign objects embedded Workpiece Inspection WoodWorkpiece Inspection Metal Basic Cutting Tips Cutting OverviewTable Tilt To make a rip cut, do these steps Guide PostRip Cutting To resaw a workpiece, do these steps CrosscuttingResawing To make a 90˚ crosscut, do these stepsTo complete a stacked cut, do these steps Cutting CurvesStacked Cuts Tooth Style Blade Characteristics Wood CuttingBlade Length Blade WidthMost common causes of blade breakage are Tooth PitchBlade Care Blade BreakageTo select the correct blade TPI, do these steps Blade Selection Metal CuttingTo replace the blade, do these steps Blade ChangesTo calibrate the scale, do these steps Fence Scale CalibrationModel D3122 Shop Fox Push Stick AccessoriesModel D3096 Shop Fox Featherboard Table & Base MaintenanceCleaning ScheduleChecking V-Belts ServiceAccessing V-Belts Servicing V-BeltsStep Follow all previous instructions for Accessing V- BeltsTensioning/Replacing V-Belts To shim the table, do these steps Shimming TableBlade Lead To skew your fence, do these steps Shimming Upper Wheel Wheel AlignmentVerifying Upper/Lower Wheels are Coplanar To adjust the lower wheel, do these steps Adjusting Lower WheelMotor junction box wiring Electrical Component WiringWiring Diagram Motor & Electrical TroubleshootingMiscellaneous Cutting OperationsWood/Metal Bandsaw PART# Description Bandsaw Body Parts ListTable & Guides Breakdown Table & Guides Parts List Fence Breakdown Label Placement M1113 18 Wood/Metal Bandsaw Comments Warranty RegistrationBOX BELLINGHAM, WA