Woodstock M1113 owner manual Setup, Inventory, Main Components Figure Qty

Page 12

M1113 18" Wood/Metal Bandsaw

SETUP

SETUP

Inventory

This machine has been carefully packaged for safe trans- portation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. The following is a description of the main components shipped with the Model M1113.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the pack- aging materials carefully. Occasionally we pre-install cer- tain components for safer shipping.

Main Components: (Figure 2)		Qty
A.	Table	1
B.	Table Extension	1
C.	Table Insert	1
D.	Rear Rail	1
E.	L-Brackets	2
F.	Front Rail	1
G.	Fence Assembly	1
H.	Miter Gauge Holder	1
I.	Miter Gauge	1

Keep machine disconnected from power until instructed otherwise.

Fasteners, Tools, & Miscellaneous: (Figure 3)		Qty
• Hex Bolts 5⁄16"-18 x 2" (Table Extension)		2
• Hex Nuts 5⁄16"-18 (Table Extension)		2
• Flat Washers 5⁄16" (Table Extension)		4
• Knobs 3⁄8"-16 (Table Trunnion)		2
• Cap Screws M6-1 x 16 (Rear Rail to Table)		2
• Cap Screws M6-1 x 16 (L-Brackets to Table)		2
• Knobs 5⁄16"-18 x 5⁄8" (L-Bracket to Front Rail)		2
• T-Slot Nuts 5⁄16" (L-Bracket to Front Rail)		2
•	Scale (Front Rail)	1
• Guide Blocks (Blade Guides)		6
• Thumb Screws 1⁄4"-20 x 1⁄2" (Blade Guides)		6
• Hex Wrenches 3 and 5mm		1 each
•	Flat Wrench 12/14mm	1

Figure 2. Main component inventory.

Figure 3. Fasteners, tools, & miscellaneous item inventory.

-10-

Image 12

Contents WOOD/METAL Bandsaw Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Electrical Specifications Electrical220V Operation Extension CordsSetup InventoryMain Components Figure Qty Machine Placement Cleaning MachineLifting & Moving To lift and move the bandsaw with a forklift, do these stepsMounting to Shop Floor Bolting to Concrete FloorsAssembly To assemble the bandsaw, do these stepsInstalling fence onto rails Dust Collection Recommended CFM at each Dust PortBlade Tracking To center track the bladeTest Run To test run the machine, do these stepsBlade Tensioning To tension the bandsaw bladeAdjustment To adjust the support bearings, do these stepsSupport Bearing Blade Guide Adjustment To adjust the upper and lower blade guides, do these stepsTable Stop Adjustment Table Tilt Scale CalibrationTable Alignment Fence AlignmentOperations GeneralBasic Controls Workpiece Inspection Wood Choosing wood without embedded foreign objects embeddedWorkpiece Inspection Metal Cutting Overview Table TiltBasic Cutting Tips Guide Post Rip CuttingTo make a rip cut, do these steps Crosscutting ResawingTo make a 90˚ crosscut, do these steps To resaw a workpiece, do these stepsCutting Curves Stacked CutsTo complete a stacked cut, do these steps Blade Characteristics Wood Cutting Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areBlade Selection Metal Cutting To select the correct blade TPI, do these stepsBlade Changes To replace the blade, do these stepsFence Scale Calibration To calibrate the scale, do these stepsAccessories Model D3096 Shop Fox FeatherboardModel D3122 Shop Fox Push Stick Maintenance CleaningSchedule Table & BaseService Accessing V-BeltsServicing V-Belts Checking V-BeltsFollow all previous instructions for Accessing V- Belts Tensioning/Replacing V-BeltsStep Shimming Table Blade LeadTo shim the table, do these steps To skew your fence, do these steps Wheel Alignment Verifying Upper/Lower Wheels are CoplanarShimming Upper Wheel Adjusting Lower Wheel To adjust the lower wheel, do these stepsElectrical Component Wiring Motor junction box wiringWiring Diagram Troubleshooting Motor & ElectricalCutting Operations MiscellaneousWood/Metal Bandsaw Bandsaw Body Parts List PART# DescriptionTable & Guides Breakdown Table & Guides Parts List Fence Breakdown Label Placement M1113 18 Wood/Metal Bandsaw Warranty Registration CommentsBOX BELLINGHAM, WA