Woodstock M1113 owner manual Assembly, To assemble the bandsaw, do these steps

Page 16

M1113 18" Wood/Metal Bandsaw

SETUP

Assembly

To assemble the bandsaw, do these steps:

1.Place the bandsaw table upside down on a flat sur- face (preferably a workbench) and make sure the table trunnion mounting bolts (Figure 9) are tight.

2.Attach the table extension to the table with the two 5⁄16-18 x 2" hex bolts, two 5⁄16-18 hex nuts, and four 5⁄16" flat washers, as shown in Figure 10. Make sure that the table and table extension are firmly pressed against the flat surface and tighten the bolts/nuts.

3.Remove the table pin from the table slot, fit the table around the blade, and rest the table trunnions on the trunnion base, making sure the trunnion bolts extend through the bottom of the trunnion base.

Table Trunnion

Mounting Bolts

Figure 9. Table trunnion mounting bolts.

Table Extension

4.Thread the two table trunnion knobs onto the trun- nion bolts, as illustrated in Figure 11.

5.Adjust the table stop bolt (Figure 12) so the table is approximately perpendicular to the blade. (Precise adjustment of the table stop bolt will be covered later.)

6.Place the table insert in the center of the table, so it sits flush with the table top surface.

7.Insert the table pin into the end of the table slot.

Figure 10. Table extension attached to

table on flat surface.

��

��

��

��

��

��

��

Figure 11. Installing the table on trunnion

base.

Table Stop

Bolt

-14-	Figure 12. Table stop bolt.

Image 16

Contents WOOD/METAL Bandsaw Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Electrical Specifications Electrical220V Operation Extension CordsInventory SetupMain Components Figure Qty Machine Placement Cleaning MachineLifting & Moving To lift and move the bandsaw with a forklift, do these stepsMounting to Shop Floor Bolting to Concrete FloorsAssembly To assemble the bandsaw, do these stepsInstalling fence onto rails Dust Collection Recommended CFM at each Dust PortBlade Tracking To center track the bladeTest Run To test run the machine, do these stepsBlade Tensioning To tension the bandsaw bladeTo adjust the support bearings, do these steps AdjustmentSupport Bearing Blade Guide Adjustment To adjust the upper and lower blade guides, do these stepsTable Stop Adjustment Table Tilt Scale CalibrationTable Alignment Fence AlignmentGeneral OperationsBasic Controls Workpiece Inspection Wood Choosing wood without embedded foreign objects embeddedWorkpiece Inspection Metal Table Tilt Cutting OverviewBasic Cutting Tips Rip Cutting Guide PostTo make a rip cut, do these steps Crosscutting ResawingTo make a 90˚ crosscut, do these steps To resaw a workpiece, do these stepsStacked Cuts Cutting CurvesTo complete a stacked cut, do these steps Blade Characteristics Wood Cutting Blade LengthBlade Width Tooth StyleTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areBlade Selection Metal Cutting To select the correct blade TPI, do these stepsBlade Changes To replace the blade, do these stepsFence Scale Calibration To calibrate the scale, do these stepsModel D3096 Shop Fox Featherboard AccessoriesModel D3122 Shop Fox Push Stick Maintenance CleaningSchedule Table & BaseService Accessing V-BeltsServicing V-Belts Checking V-BeltsTensioning/Replacing V-Belts Follow all previous instructions for Accessing V- BeltsStep Blade Lead Shimming TableTo shim the table, do these steps To skew your fence, do these steps Verifying Upper/Lower Wheels are Coplanar Wheel AlignmentShimming Upper Wheel Adjusting Lower Wheel To adjust the lower wheel, do these stepsElectrical Component Wiring Motor junction box wiringWiring Diagram Troubleshooting Motor & ElectricalCutting Operations MiscellaneousWood/Metal Bandsaw Bandsaw Body Parts List PART# DescriptionTable & Guides Breakdown Table & Guides Parts List Fence Breakdown Label Placement M1113 18 Wood/Metal Bandsaw Warranty Registration CommentsBOX BELLINGHAM, WA