Woodstock M1113 owner manual Label Placement

Page 55

M1113 18" Wood/Metal Bandsaw

Label Placement

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

��

��

��

��

��	��

��

��

��

��	��

��

		��
REF	PART�#	DESCRIPTION
301	XM1113301	BLADE�TENSION�SCALE
302	XLABEL-06	GLASSES�RESPIRATOR�LABEL
303	XLABEL-08	READ�MANUAL�LABEL
304	XM1113304	MOTOR�ON/OFF�LABEL
305	XM1113305	VARIABLE�SPEED�LABEL
306	XM1113306	BLADE�SPEED�CHART�LABEL
307	XPPAINT-1	SHOP�FOX�WHITE�PAINT

��

��

REF	PART�#	DESCRIPTION
308	XM1113308	M1113�MODEL�#�LABEL
309	XM1113309	DECORATIVE�BLACK�STRIPE
310	XLABEL-04	ELECTRICITY�LABEL
311	XLABEL-05	DOOR�CLOSED�LABEL
312	XLABEL-07	UNPLUG�POWER�LABEL
313	XM1113313	MACHINE�ID�LABEL
314	XM1113314	SHOP�FOX�LOGO�PLATE

PARTS

-53-

Image 55

Contents WOOD/METAL Bandsaw Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Extension Cords Electrical SpecificationsElectrical 220V OperationInventory SetupMain Components Figure Qty Cleaning Machine Machine PlacementTo lift and move the bandsaw with a forklift, do these steps Lifting & MovingBolting to Concrete Floors Mounting to Shop FloorTo assemble the bandsaw, do these steps AssemblyInstalling fence onto rails Recommended CFM at each Dust Port Dust CollectionTo center track the blade Blade TrackingTo test run the machine, do these steps Test RunTo tension the bandsaw blade Blade TensioningTo adjust the support bearings, do these steps AdjustmentSupport Bearing To adjust the upper and lower blade guides, do these steps Blade Guide AdjustmentTable Tilt Scale Calibration Table Stop AdjustmentFence Alignment Table AlignmentGeneral OperationsBasic Controls Choosing wood without embedded foreign objects embedded Workpiece Inspection WoodWorkpiece Inspection Metal Table Tilt Cutting OverviewBasic Cutting Tips Rip Cutting Guide PostTo make a rip cut, do these steps To resaw a workpiece, do these steps CrosscuttingResawing To make a 90˚ crosscut, do these stepsStacked Cuts Cutting CurvesTo complete a stacked cut, do these steps Tooth Style Blade Characteristics Wood CuttingBlade Length Blade WidthMost common causes of blade breakage are Tooth PitchBlade Care Blade BreakageTo select the correct blade TPI, do these steps Blade Selection Metal CuttingTo replace the blade, do these steps Blade ChangesTo calibrate the scale, do these steps Fence Scale CalibrationModel D3096 Shop Fox Featherboard AccessoriesModel D3122 Shop Fox Push Stick Table & Base MaintenanceCleaning ScheduleChecking V-Belts ServiceAccessing V-Belts Servicing V-BeltsTensioning/Replacing V-Belts Follow all previous instructions for Accessing V- BeltsStep Blade Lead Shimming TableTo shim the table, do these steps To skew your fence, do these steps Verifying Upper/Lower Wheels are Coplanar Wheel AlignmentShimming Upper Wheel To adjust the lower wheel, do these steps Adjusting Lower WheelMotor junction box wiring Electrical Component WiringWiring Diagram Motor & Electrical TroubleshootingMiscellaneous Cutting OperationsWood/Metal Bandsaw PART# Description Bandsaw Body Parts ListTable & Guides Breakdown Table & Guides Parts List Fence Breakdown Label Placement M1113 18 Wood/Metal Bandsaw Comments Warranty RegistrationBOX BELLINGHAM, WA