Woodstock W1679 instruction manual 110V Operation, Extension Cords, Grounding

Page 10

SAFETY

110V Operation

The Shop Fox® W1679 is prewired for 110 volts. The motor supplied with your new machine is rated at 1 HP and will draw approximately 14 amps. When choosing an outlet for this machine, consider using one with a 15 amp circuit break- er or fuse. When choosing plug and outlet, use a NEMA-style 5-15 as shown in Figure 6. Keep in mind that a circuit being used by other machines or tools at the same time will add to the elec- trical load being applied by the machine. Add up the load ratings of all machines on the circuit. If this number exceeds the rating of the circuit breaker or fuse, use a different circuit.

Do not remove the ground- ing pin from any plug and always make sure all wiring to the machine is grounded before operating. Any elec- trical outlet and circuit that you plug your machine into must be grounded. Serious injury may occur if this warning is ignored!

Extension Cords

When it is necessary to use an extension cord, use the following guidelines:

•Use cords rated for Hard Service •Never exceed a length of 100 feet •Use cords with 14 ga. wire or bigger (12 ga., 10 ga., etc.)

•Make sure cord has a ground wire and pin •Do not use damaged cords

Figure 6. NEMA-style 5-15 plug and outlet.

Grounding

This machine must be grounded! The electrical cord supplied with the Model W1679 comes with a grounding pin. Do not remove it. See Figure 7. If your outlet does not accommodate a ground pin, have it replaced by a qualified electrician or have an appropriate adapter installed. Please note: when using an adapter, the adapter must be grounded.

An adapter with a grounding wire does not guar- antee the machine will be grounded. A ground source must be verified.

Figure 7. Never remove grounding pin.

-8-

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Jointer Page Table Of Contents Introduction Woodstock Service And SupportAbout Your New Jointer Warranty And Returns Machine SpecificationsSafety Standard Safety Instructions#18 #16 #14 11-12 13-16 #12 17-20 #10 21-30 Keep your footing stable and keep your balance at all timesAdditional Safety Instructions For Jointers Avoiding Potential Injuries Never surface plane without push blocksExtension Cords 110V OperationGrounding 220V Operation NEMA-style 6-15 plug and outletBox Contents Assembly InstructionsUnpacking Shop Preparation Cleaning Machine Beginning Installing V-BeltMounting Jointer Installing Fence Dust PortInstalling lock knob and special nut Pivot Cutterhead GuardControl Pedestal Belt GuardKnife Gauge To assemble the knife gaugeAdjustments Checking KnivesAdjusting Knives To adjust the knives Unplug the jointerTo adjust the outfeed table Unplug the jointer Adjusting TablesTo adjust the table gibs Unplug the jointer Table GibsTo adjust the infeed table Infeed table even with outfeed Scale can now be set toTo check/adjust the fence stops Unplug the jointer Fence StopsStarting Jointer OperationsBasic Operations Only plane clean stock Operation MustsSurface Planing To perform a surface planing operationEdge Jointing To perform an edge jointing operationBevel Cutting To perform a bevel cutting operationRabbet Cutting To perform a rabbet cutting operationGeneral MaintenanceTable Surface Replacing V-Belt LubricationSharpening Knives To replace the V-belt Unplug the jointerTroubleshooting Symptom Possible Reason HOW to RemedyFeed Direction Maintenance Parts Parts 120 112 119 104 132 103 130 XPW07 Flat Washer 5⁄16 XPB21 208 242 243 232 209 221 213 229 226 316 Infeed Table Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents