Woodstock W1679 instruction manual Cutterhead Guard, Installing lock knob and special nut Pivot

Page 16

ASSEMBLY

4.Place the 1⁄2" flat washer over the lock knob and install the special nut from underneath the fence support as shown in Figure 15.

5.Make sure the splines on the special nut pro- trude into the adjustment slot, then insert the knob through the fence housing and thread the knob into the special nut.

Cutterhead Guard

1.Remove the setscrew from the slot in the end of the cutterhead guard shaft.

2.Rotate the spring housing clockwise (looking at the face of the knob) 1 full turn and insert the cutterhead shaft into the pivot hole as shown in Figure 16.

3.Fit the shaft slot over the tang inside the spring housing. The shaft should drop through the bottom of the housing.

4.When installed, the cutterhead guard should press firmly against the fence and should be completely covering the cutter- head as shown in Figure 17.

5.Move the cutterhead guard back and forth to make sure that it automatically returns back to its proper position against the fence and over the cutterhead.

6.Make sure the cutterhead guard has the correct return pressure. If the pressure is weak or there is no return pressure at all, remove the shaft, tighten the spring housing by rotating clockwise, and re-install the shaft to check for proper operation.

7.Replace the setscrew at the end of the shaft, so that the cutterhead guard cannot be removed from the pivot hole.

Lock

Knob

Tilt

Knob

Special

Nut

Figure 15. Installing lock knob and special nut.

 

Pivot

Cutterhead

Hole

Guard

 

Shaft

Spring

 

 

Housing

Figure 16. Rotate spring housing clockwise 1 full turn and insert cutterhead guard shaft.

Figure 17. Guard in proper position against the fence and completely over the cutterhead.

-14-

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Jointer Page Table Of Contents Introduction Woodstock Service And SupportAbout Your New Jointer Warranty And Returns Machine SpecificationsSafety Standard Safety Instructions#18 #16 #14 11-12 13-16 #12 17-20 #10 21-30 Keep your footing stable and keep your balance at all timesAdditional Safety Instructions For Jointers Avoiding Potential Injuries Never surface plane without push blocksExtension Cords 110V OperationGrounding 220V Operation NEMA-style 6-15 plug and outletBox Contents Assembly InstructionsUnpacking Shop Preparation Cleaning Machine Beginning Installing V-BeltMounting Jointer Installing Fence Dust PortInstalling lock knob and special nut Pivot Cutterhead GuardBelt Guard Knife GaugeControl Pedestal To assemble the knife gaugeAdjustments Checking KnivesAdjusting Knives To adjust the knives Unplug the jointerAdjusting Tables To adjust the table gibs Unplug the jointerTo adjust the outfeed table Unplug the jointer Table GibsTo adjust the infeed table Infeed table even with outfeed Scale can now be set toTo check/adjust the fence stops Unplug the jointer Fence StopsStarting Jointer OperationsBasic Operations Only plane clean stock Operation MustsSurface Planing To perform a surface planing operationEdge Jointing To perform an edge jointing operationBevel Cutting To perform a bevel cutting operationRabbet Cutting To perform a rabbet cutting operationGeneral MaintenanceTable Surface Lubrication Sharpening KnivesReplacing V-Belt To replace the V-belt Unplug the jointerTroubleshooting Symptom Possible Reason HOW to RemedyFeed Direction Maintenance Parts Parts 120 112 119 104 132 103 130 XPW07 Flat Washer 5⁄16 XPB21 208 242 243 232 209 221 213 229 226 316 Infeed Table Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents