Woodstock W1754S owner manual Columns Breakdown

Page 10

W1754S 20" Planer with Spiral Cutterhead

Columns Breakdown

,',

,'(

,('

,'-

,'.

,(0

,)*

,)( ,))

,)+

	,((		,(/
	,((		,(-
			,(-
		,(,	,'0
	,'/	,(,	,(+
	,'/

		,*)	,(*
			,(*
			,(.

,()

,*( ,)'

,*' ,')

	,)0		,'+
	,).		,'*
	,).	,**	,)/
	,),	,**	,)/
	,),

,)-

REF	PART #	DESCRIPTION
501	X1754501	BASE
502	XPB38M	HEX BOLT M12-1.75 X 60
503	XPN09M	HEX NUT M12-1.75
504	XPW06M	FLAT WASHER 12MM
505	X1754505	COLUMN
506	XP6202ZZ	BALL BEARING 6202ZZ
507	XPR21M	INT RETAINING RING 35MM
508	X1754508	COLUMN
509	XPR22M	INT RETAINING RING 38MM
510	XPSS13M	SET SCREW M10-1.5 X 12
511	X1754511	LEAD SCREW
512	X1754512	LEAD SCREW
513	X1754513	LEAD NUT
514	XPSB14M	CAP SCREW M8-1.25 X 20
515	X1754515	BUSHING
516	X1754516	GEAR
517	XPK69M	KEY 4 X 4 X 12

REF	PART #	DESCRIPTION
518	XPR03M	EXT RETAINING RING 12MM
519	X1754519	SPROCKET
520	XPK08M	KEY 5 X 5 X 16
521	XPW04M	FLAT WASHER 10MM
522	XPN02M	HEX NUT M10-1.5
523	X1754523	BRACKET ASSEMBLY
524	XPR05M	EXT RETAINING RING 15MM
525	XPB07M	HEX BOLT M8-1.25 X 25
526	X1754526	SPROCKET
527	XPW01M	FLAT WASHER 8MM
528	X1754528	CRANE POST
529	XPR81M	EXT RETAINING RING 21MM
530	X1754530	PIPE BAND
531	XPS09M	PHLP HD SCR M5-.8 X 10
532	X1754532	DUST BOOT
533	X1754533	CHAIN 08A-1 X 66

-10-

Image 10

Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Headstock Parts List DescriptionGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Introduction Woodstock Technical SupportIntroduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Electrical Specifications220V Operation Unpacking SetupItems Needed for Setup InventoryLifting Planer Machine PlacementHardware and Tools Not Shown Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the caster and foot pedal, do these steps To install the handwheel, do these stepsHandwheel, Dust Hood Caster Gearbox Oil Level Connecting to PowerTo check the gearbox oil level, do these steps Test Run To perform a test run, do these stepsRecommended Adjustments Tighten V-BeltsBasic Operation OperationsGeneral Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsTo adjust the bed rollers, do these steps Adjustment Height Range 002-0.020Bed Rollers Accessories Planer AccessoriesOperations Cleaning MaintenanceMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsPulley Alignment on Lubrication Inspecting Knives ServiceTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCLocation Service To adjust roller spring tension, do these steps Spring TensionLoosen the chip deflector mounting bolts see Figure Scale CalibrationTo calibrate the scale, do these steps Anti-Kickback Fingers Anti-kickback fingersPulley Alignment Example of checking belt AlignmentW1754 Electrical Components Motor junction boxW1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective ActionCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration CommentsBOX BELLINGHAM, WA