Woodstock W1754S Scale Calibration, Loosen the chip deflector mounting bolts see Figure

Page 49

W1754 20" Planer With Mobile Base

Chip Deflector Positioning

The chip deflector keeps chips from falling onto the outfeed roller.

Chip Deflector Gap Setting	1⁄4"
To adjust the deflector position, do these steps:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Put on leather gloves.

3.Remove the dust hood, top cover, and V-belt cover.

4.Loosen the chip deflector mounting bolts (see Figure 35).

5.Make sure the deflector is beveled toward the cutterhead. Move the deflector until the edge is the correct distance (given above) from the knife edge.

6.Rotate the cutterhead to ensure clearance by turn- ing the cutterhead pulley.

7.Re-tighten the mounting bolts and reinstall the top cover, dust hood, and V-belt cover on the planer.

Chip Deflector

OFF

Chip Deflector

Mounting Bolts

Figure 35. Chip deflector and mounting

bolts.

Scale Calibration
The scale can be adjusted for accuracy. The machine will
need to be run to calibrate the scale.	Figure 36. Depth scale adjustment screws.
	Figure 36. Depth scale adjustment screws.
To calibrate the scale, do these steps:

1.Set the table to the approximate thickness of your test lumber. Measure the lumber with calipers to determine its exact thickness.

2.Move the table to 1⁄16" under the thickness of your lumber and feed your test board through the planer.

3.Turn the handwheel one full rotation and run the board through once more. Turn the board over and repeat.

4.Re-measure the board and compare your results with the scale. If there is a discrepancy, loosen the screws (see Figure 36) and adjust as necessary.

-35-

SERVICE

Image 49

Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Electrical Specifications220V Operation Items Needed for Setup SetupUnpacking InventoryLifting Planer Machine PlacementHardware and Tools Not Shown These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the caster and foot pedal, do these steps To install the handwheel, do these stepsHandwheel, Dust Hood Caster Gearbox Oil Level Connecting to PowerTo check the gearbox oil level, do these steps To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsGeneral OperationsBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed control knob positions Feed SpeedTo adjust the bed rollers, do these steps Adjustment Height Range 002-0.020Bed Rollers Planer Accessories AccessoriesOperations Cleaning MaintenanceMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsPulley Alignment on Lubrication Inspecting Knives ServiceTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsLoosen the chip deflector mounting bolts see Figure Scale CalibrationTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA