Woodstock W1754S owner manual Table Breakdown

Page 9

W1754S 20" Planer with Spiral Cutterhead

Table Breakdown

+'0

+'.

+'/

+',

+'+ +'*

+')

+'-

+'(

+('

+(+ +()

+(( +(*

REF	PART #	DESCRIPTION
401	X1754401	TABLE/BED
402	X1754402	ROLLER
403	XP6201	BALL BEARING 6201
404	X1754404	ECCENTRIC SHAFT
405	XPSS04M	SET SCREW M6-1 X 12
406	X1754406	LOCK BAR
407	X1754407	LOCK SLEEVE

REF	PART #	DESCRIPTION
408	X1754408	LOCKING ROD
409	X1754409	STAR KNOB M12-1.75
410	X1754410	EXTENSION WING
411	XPLW04M	LOCK WASHER 8MM
412	XPW01M	FLAT WASHER 8MM
413	XPB20M	HEX BOLT M8-1.25 X 35
414	XPSS09M	SET SCREW M8-1.25 X 20

-9-

Image 9

Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Items Needed for Setup SetupUnpacking InventoryMachine Placement Lifting PlanerHardware and Tools Not Shown These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsGeneral OperationsBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed control knob positions Feed SpeedAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories AccessoriesOperations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsScale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA