Woodstock W1754S owner manual Operations, General, Basic Operation

Page 31

W1754 20" Planer With Mobile Base

OPERATIONS

General

The Model W1754 will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incor- rectly.

The instructions in this section are written with the under- standing that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine!

If you are an inexperienced operator, we strongly recom- mend that you read books, trade articles, or seek training from an experienced planer operator before performing any unfamiliar operations. Above all, your safety should come first!

READ and understand this entire instruc- tion manual before using this machine. Serious personal injury may occur if safety and operational information is not understood and followed. DO NOT risk your safety by not reading!

Basic Operation

The table moves approximately 1/16" with one turn of the handwheel.

The basic steps of operating the planer are as follows:

1.Put on safety glasses, respirator, and hearing protec- tion.

2.Unless your workpiece is very flat, surface plane one face of the workpiece on a jointer until it is flat—having the face flat will ensure that it sits flat on the planer table during operation.

3.Adjust the table height slightly lower than your workpiece to ensure the first cut is as light as pos- sible (approximately 1/32"–1/16"). This cut removes any excessive high spots.

4.Start the planer.

5.Making sure not to stand directly in front or behind the workpiece to avoid kickback injury, place the flat side of the board down on the table, and feed the workpiece through the planer.

—If the cut is too heavy and bogs down the planer, turn the planer OFF immediately, allow it to come to a complete stop, and remove the workpiece. Lower the table, then repeat Steps 2–5.

-17-

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

OFF

DO NOT investigate problems or adjust the planer while it is running. Wait until the machine is turned OFF and all working parts have come to a complete stop before proceeding!

OPERATIONS

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Electrical Specifications220V Operation Inventory SetupItems Needed for Setup UnpackingLifting Planer Machine PlacementHardware and Tools Not Shown These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the caster and foot pedal, do these steps To install the handwheel, do these stepsHandwheel, Dust Hood Caster Gearbox Oil Level Connecting to PowerTo check the gearbox oil level, do these steps To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedTo adjust the bed rollers, do these steps Adjustment Height Range 002-0.020Bed Rollers Planer Accessories AccessoriesOperations Cleaning MaintenanceMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsPulley Alignment on Lubrication Inspecting Knives ServiceTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsLoosen the chip deflector mounting bolts see Figure Scale CalibrationTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents