Woodstock W1754S Rollers, Breaker Pressure Bar Heights, Distance Below Knife Edge at *BDC

Page 45

W1754 20" Planer With Mobile Base

Rollers, Breaker &

Pressure Bar Heights

Depending upon the type of wood, feed rate, and depth of cut, you may have to vary the below adjustments a few thousands of an inch. No single adjustment works for all wood, feed rates or depths of cuts.

To ensure accurate results and make the adjustment pro- cess quicker and easier, we recommend using a Rotacator (see Page 21) for these adjustments.

If a Rotacator is not available, a 6' 2x4 cut into two even sized pieces and a feeler gauge set can be used, but care must be taken when jointing the blocks to achieve accu- rate results.

Distance Below Knife Edge at *BDC:
Infeed Roller	0.040"
Chip Breaker	0.040"
Pressure Bar	0.008"
Outfeed Roller	0.020"

*BDC = Bottom Dead Center (see Figure 28).

To set the height of the infeed and outfeed rollers, chip breaker, and pressure bar using a Rotacator, do these steps:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Make sure the knives are set correctly with the knife gauge.

3.Lower the table at least 4" below the headstock and lock the table in place.

4.Remove the dust hood, top cover, and V-belt cover.

5.Using your Rotacator, find BDC of any knife edge by slowly rocking the cutterhead pulley back and forth, and set the Rotacator dial to zero, as shown in

Figure 29.

6.Place the Rotacator under the right-hand side of the infeed roller, and find bottom dead center on a serrated edge by rocking the infeed roller back and forth.

��

��

Figure 28. Knife edge at bottom dead

center.

OFF

Figure 29. Finding BDC with the

Rotacator.

SERVICE

-31-

Image 45

Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Items Needed for Setup SetupUnpacking InventoryMachine Placement Lifting PlanerHardware and Tools Not Shown These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsGeneral OperationsBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed control knob positions Feed SpeedAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories AccessoriesOperations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsScale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA