Woodstock W1754S owner manual Test Run, To perform a test run, do these steps

Page 29

W1754 20" Planer With Mobile Base

Test Run

Complete this test run process once you have familiarized yourself with all instructions in this manual and taken all safety precautions. The purpose of the test run is to make sure that the motor and EMERGENCY STOP button work properly before proceeding.

To perform a test run, do these steps:

1.Read the entire manual, and make sure the gearbox oil level is full (Refer to the Lubrication section on

Page 25).

2.Make sure all tools and foreign objects have been removed from the planer.

3.Make sure the feed control knob is pushed in or out all the way (Refer to Feed Speed, Page 19).

4.Put on safety glasses, and secure loose clothes or long hair.

5.Press the green START button to turn the machine ON (Figure 42). The START button should illuminate and the planer should run smoothly with little or no vibration.

—If you suspect any problems, immediately turn the planer OFF by pushing the red STOP button. Refer to Page 40 to troubleshoot/fix any problems before starting the planer again.

—If the source of an unusual noise or vibration is not readily apparent, contact our technical support for help at (360) 734-3482 or contact us online at tech-support@shopfox.biz.

6.Press the STOP button in.

7.Press the START button in. The machine should not run and the START button should not illuminate.

—If the STOP button is working correctly, turn it clockwise until it pops out. The machine is ready for operation.

—If the planer starts, the STOP button is not working correctly. Immediately DISCONNECT THE PLANER FROM POWER! and contact our technical support before proceeding further.

-15-

SET UP

Image 29

Contents Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers 220V Operation Electrical SpecificationsElectrical Items Needed for Setup SetupUnpacking InventoryHardware and Tools Not Shown Machine PlacementLifting Planer These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsHandwheel, Dust Hood Caster To install the handwheel, do these stepsTo install the caster and foot pedal, do these steps To check the gearbox oil level, do these steps Connecting to PowerGearbox Oil Level To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsGeneral OperationsBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed control knob positions Feed SpeedBed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Planer Accessories AccessoriesOperations Maintenance Schedule MaintenanceCleaning Pulley Alignment on To adjust/replace the V-belts, do these stepsBelts Lubrication To inspect the knives, do these steps ServiceInspecting Knives To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Scale CalibrationLoosen the chip deflector mounting bolts see Figure Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA