RIDGID TS2410LS manual OPERATOR’S Manual

Page 1

OPERATOR’S MANUAL

10 in. TABLE SAW

TS2410LS

Your table saw has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING:

To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

Thank you for buying a RIDGID® product.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Image 1
Contents OPERATOR’S Manual Introduction Table of Contents Guard Against Electrical Shock by Prevent General Safety Rules Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Speed and WiringExtension Cords Grounding InstructionsGlossary of Terms Product Specifications FeaturesSee Figure Know Your Table SAWOperating Components Switch AssemblyTools Needed Loose Parts ListUnpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace To SECURE/LEVEL the SAW To Store the Table SAW AccessoriesWing NUT WingSee Figures 12 To Close the LEG Stand and Move the SAWTo close the leg stand To move the leg standTo REMOVE/REPLACE the Throat Plate To Check the Throat PlateTo align the throat plate with the saw table SET Screws Removing Throat PlateTo Install Blade Guard Assembly To Check SAW Blade InstallationOperation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding KickbackCutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Change Blade Angle To Change Blade DepthTo USE the IND-I-CUT Disc Once the Ind-I-Cut is levelTo USE the MICRO-ADJUST Wheel on the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the RIP Fence Back RIP FenceTo USE the Table Extension To USE the Miter GaugeStop PIN To UnlockSee Figures 32 Heeling Paralleling the Blade to the Miter Gauge GrooveRight Miter Gauge Groove Combination Square Aligning Screws Blade TOO Close to Miter Gauge GrooveMaking a Cross CUT Switch OFF Switch onSee Figures 35 Cross CUT Place Hands on Workpiece Miter Gauge Lock KnobMaking a Miter CUT Making a RIP CUTRIP CUT BladeMaking a Bevel Cross CUT HEIGHT/BEVEL Adjusting HandwheelSee Figures 39 Viewed from the FRONT, below the Table SAWMaking a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Dado CUT Making a Dado CUTTo install a standard blade AdjustmentsTo Replace the Blade See Figures 46See Figures 48 To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚If blade is square to the table If blade is not square to the tableBlade AT 45˚ Position To Adjust the Miter GaugeScrew Lock Knob Miter Gauge ROD Flat Head Screw SET ScrewHEX Head Bolt Adjusting NUT Locking Lever Back Rail To Check and Adjust the Alignment RIP FenceSee Figures 54 Locking LeverTo Adjust the Table Extension To Adjust the Bevel Locking LeverChecking the Table Extension Bevel Lock NUT Front HEX CouplingGeneral Maintenance MaintenanceNylon SET Screw Adjustment LubricationBrush Replacement AccessoriesBrush CAP Assembly See To Check and Align the Blade Guard TroubleshootingSee To Adjust the Miter Gauge See To Set the Bevel IndicatorAdjustments section Bevel Stops at 0˚ and 45˚ SquaringPage DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No TS2410LS Serial No Customer Service Information