RIDGID TS2410LS manual To Adjust the Bevel Locking Lever, Checking the Table Extension

Page 39

ADJUSTMENTS

TO ADJUST THE BEVEL LOCKING LEVER

See Figure 57.

Release bevel locking lever and bevel saw blade to 45º.

Push bevel locking lever to lock blade into place.

With moderate force, attempt to move the height/bevel adjusting handwheel toward the 0º bevel.

If height/bevel adjusting handwheel cannot be moved, no adjustment is needed. If handwheel can be moved, adjust the bevel lock nut by rotating clockwise 1/4 turn.

Repeat above step as necessary.

Release bevel locking lever and move height/bevel adjusting handwheel back to 0º.

CHECKING THE TABLE EXTENSION

See Figure 58.

Lock the sliding table extension. The sliding table extension should not move while locked. If the extension moves:

Lift the table extension lock lever.

Find the front hex coupling located underneath the front table.

Loosen the hex locking nut.

Turn the hex coupling counterclockwise.

Lock the table extension lock. Push and pull on the sliding table extension.

Readjust hex coupling if necessary.

Tighten the hex locking nut against coupling.

TO ADJUST THE TABLE EXTENSION

See Figure 59.

Lock table extension lever.

Loosen the four nuts underneath the sliding table extension.

Use a combination square to make sure the top of the sliding table extension is the same height as the main table.

Tighten the four hex nuts. Recheck and readjust if necessary.

BEVEL LOCK NUT

Fig. 57

FRONT HEX

COUPLING

HEX

 

LOCKING

 

NUT

Fig. 58

 

COMBINATION

SQUARE

HEX NUT

EXTENSION

TABLE

Fig. 59

39

Image 39
Contents OPERATOR’S Manual Introduction Table of Contents Guard Against Electrical Shock by Prevent General Safety RulesSpecific Safety Rules  Before Making a CUT, be Sure ALL Adjust Ments are Secure Blade Coasts After Being Turned OFF Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceGrounding Instructions Speed and WiringElectrical Extension CordsGlossary of Terms Product Specifications FeaturesSee Figure Know Your Table SAWOperating Components Switch AssemblyTools Needed Loose Parts ListAssembly UnpackingMounting Holes To Open the LEG Stand See Figures 7Release Lever Grips LEG Stand Center Brace Wing To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW Wing NUTTo move the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To close the leg standSET Screws Removing Throat Plate To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate To align the throat plate with the saw tableTo Install Blade Guard Assembly To Check SAW Blade InstallationTo Check and Align the Blade Guard Assembly OperationANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Avoiding Kickback ApplicationsBasic Operation of the Table SAW Causes of KickbackTypes of Cuts Cutting TipsCross CUT HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard Once the Ind-I-Cut is level To Change Blade DepthTo Change Blade Angle To USE the IND-I-CUT DiscBack RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence To USE the RIP FenceTo Unlock To USE the Miter GaugeTo USE the Table Extension Stop PINBlade TOO Close to Miter Gauge Groove Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Right Miter Gauge Groove Combination Square Aligning ScrewsCross CUT Place Hands on Workpiece Miter Gauge Lock Knob Switch OFF Switch onMaking a Cross CUT See Figures 35Blade Making a RIP CUTMaking a Miter CUT RIP CUTViewed from the FRONT, below the Table SAW HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT See Figures 39Making a Bevel RIP CUT Making a Compound Bevel Miter CUT Making a Large Panel CUTSupports Large Panel CUT Making a NON-THROUGH CUT Dado CUT Making a Dado CUTSee Figures 46 AdjustmentsTo install a standard blade To Replace the BladeIf blade is not square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is square to the tableFlat Head Screw SET Screw To Adjust the Miter GaugeBlade AT 45˚ Position Screw Lock Knob Miter Gauge RODLocking Lever To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail See Figures 54Bevel Lock NUT Front HEX Coupling To Adjust the Bevel Locking LeverTo Adjust the Table Extension Checking the Table ExtensionLubrication MaintenanceGeneral Maintenance Nylon SET Screw AdjustmentAccessories Brush ReplacementBrush CAP Assembly See To Check and Align the Blade Guard TroubleshootingBevel Stops at 0˚ and 45˚ Squaring See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Adjustments sectionPage HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No TS2410LS Serial No Customer Service Information