RIDGID TS2410LS manual Accessories, Brush Replacement, Brush CAP Assembly

Page 41

MAINTENANCE

BRUSH REPLACEMENT

See Figure 61.

Unplug the saw.

Lower blade completely and bevel to 45º. Lock the blade.

Turn saw upside down.

Remove brush caps with a screwdriver.

NOTE: Brush assembly is spring load and will pop out when brush cap is removed.

Remove brush assemblies and check for wear.

Replace both brushes when either has less than 1/4 in. length of carbon remaining. Do not replace one side without replacing the other.

Reassemble using new brush assemblies by reversing the steps listed above. Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube.

Tighten all brush caps securely. Do not overtighten.

BRUSH

CAP

BRUSH

ASSEMBLY

Fig. 61

ACCESSORIES

Look for these accessories where you purchased this product:

AC1022 Miter Gauge Hold Down

AC1040 Molding/Dado Throat Plate

AC1045 Zero Clearance Throat Plate

AC9933 Flip Top Portable Work Support

WARNING:

Current attachments and accessories available for use with this tool are listed above. Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

41

Image 41

Contents OPERATOR’S Manual Introduction Table of Contents Guard Against Electrical Shock by Prevent General Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Speed and WiringExtension Cords Grounding InstructionsGlossary of Terms Product Specifications FeaturesSee Figure Know Your Table SAWOperating Components Switch AssemblyTools Needed Loose Parts ListMounting Holes AssemblyUnpacking Release Lever Grips LEG Stand Center Brace To Open the LEG StandSee Figures 7 To SECURE/LEVEL the SAW To Store the Table SAW AccessoriesWing NUT WingSee Figures 12 To Close the LEG Stand and Move the SAWTo close the leg stand To move the leg standTo REMOVE/REPLACE the Throat Plate To Check the Throat PlateTo align the throat plate with the saw table SET Screws Removing Throat PlateTo Install Blade Guard Assembly To Check SAW Blade InstallationANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader To Check and Align the Blade Guard AssemblyOperation Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding KickbackCross CUT Types of CutsCutting Tips Featherboard HOW to Mount a FeatherboardHOW to Make a Featherboard To Change Blade Angle To Change Blade DepthTo USE the IND-I-CUT Disc Once the Ind-I-Cut is levelTo USE the MICRO-ADJUST Wheel on the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the RIP Fence Back RIP FenceTo USE the Table Extension To USE the Miter GaugeStop PIN To UnlockSee Figures 32 Heeling Paralleling the Blade to the Miter Gauge GrooveRight Miter Gauge Groove Combination Square Aligning Screws Blade TOO Close to Miter Gauge GrooveMaking a Cross CUT Switch OFF Switch onSee Figures 35 Cross CUT Place Hands on Workpiece Miter Gauge Lock KnobMaking a Miter CUT Making a RIP CUTRIP CUT BladeMaking a Bevel Cross CUT HEIGHT/BEVEL Adjusting HandwheelSee Figures 39 Viewed from the FRONT, below the Table SAWMaking a Bevel RIP CUT Supports Large Panel CUT Making a Compound Bevel Miter CUTMaking a Large Panel CUT Making a NON-THROUGH CUT Dado CUT Making a Dado CUTTo install a standard blade AdjustmentsTo Replace the Blade See Figures 46See Figures 48 To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚If blade is square to the table If blade is not square to the tableBlade AT 45˚ Position To Adjust the Miter GaugeScrew Lock Knob Miter Gauge ROD Flat Head Screw SET ScrewHEX Head Bolt Adjusting NUT Locking Lever Back Rail To Check and Adjust the Alignment RIP FenceSee Figures 54 Locking LeverTo Adjust the Table Extension To Adjust the Bevel Locking LeverChecking the Table Extension Bevel Lock NUT Front HEX CouplingGeneral Maintenance MaintenanceNylon SET Screw Adjustment LubricationBrush CAP Assembly AccessoriesBrush Replacement See To Check and Align the Blade Guard TroubleshootingSee To Adjust the Miter Gauge See To Set the Bevel IndicatorAdjustments section Bevel Stops at 0˚ and 45˚ SquaringPage DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No TS2410LS Serial No Customer Service Information