RIDGID manual Customer Service Information, Model No TS2410LS Serial No

Page 46

OPERATOR’S MANUAL

10 in. TABLE SAW

TS2410LS

CUSTOMER SERVICE INFORMATION

For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com.

The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided below. When ordering repair parts, always give the following information:

Model No.

TS2410LS

 

Serial No.

 

 

987000-213

10-18-07 (REV:00)

Image 46
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules  Guard Against Electrical Shock by Prevent Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningExtension Cords Speed and WiringElectrical Grounding InstructionsGlossary of Terms Features Product SpecificationsKnow Your Table SAW See FigureSwitch Assembly Operating ComponentsLoose Parts List Tools NeededUnpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace Wing NUT To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW WingTo close the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To move the leg standTo align the throat plate with the saw table To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate SET Screws Removing Throat PlateTo Check SAW Blade Installation To Install Blade Guard AssemblyOperation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Causes of Kickback ApplicationsBasic Operation of the Table SAW Avoiding KickbackCutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To USE the IND-I-CUT Disc To Change Blade DepthTo Change Blade Angle Once the Ind-I-Cut is levelTo USE the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence Back RIP FenceStop PIN To USE the Miter GaugeTo USE the Table Extension To UnlockRight Miter Gauge Groove Combination Square Aligning Screws Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Blade TOO Close to Miter Gauge GrooveSee Figures 35 Switch OFF Switch onMaking a Cross CUT Cross CUT Place Hands on Workpiece Miter Gauge Lock KnobRIP CUT Making a RIP CUTMaking a Miter CUT BladeSee Figures 39 HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT Viewed from the FRONT, below the Table SAWMaking a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Making a Dado CUT Dado CUTTo Replace the Blade AdjustmentsTo install a standard blade See Figures 46If blade is square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is not square to the tableScrew Lock Knob Miter Gauge ROD To Adjust the Miter GaugeBlade AT 45˚ Position Flat Head Screw SET ScrewSee Figures 54 To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail Locking LeverChecking the Table Extension To Adjust the Bevel Locking LeverTo Adjust the Table Extension Bevel Lock NUT Front HEX CouplingNylon SET Screw Adjustment MaintenanceGeneral Maintenance LubricationBrush Replacement AccessoriesBrush CAP Assembly Troubleshooting See To Check and Align the Blade GuardAdjustments section See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Bevel Stops at 0˚ and 45˚ SquaringPage What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS2410LS Serial No