RIDGID TS2410LS To USE the Miter Gauge, To USE the Table Extension, Stop PIN, To Unlock, To Lock

Page 26

OPERATION

TO USE THE MITER GAUGE

See Figure 30.

��The miter gauge provides greater accuracy in angled cuts. For very close tolerances, test cuts are recommended.

There are two miter gauge channels, one on either side of the blade. When making a 90° cross cut, you can use either miter gauge channel. When making a beveled cross cut (the blade tilted in relation to the table) the miter gauge should be located in the slot on the right so that the blade is tilted away from the miter gauge and your hands.

The miter gauge can be turned 60° to the right or left. Posi- tive stops at 0° and 45° can be located by pushing in the stop pin.

Slide the miter gauge in the miter gauge slot.

Loosen the lock knob by turning it counterclockwise.

Pull out the stop pin and rotate the gauge until the desired angle is reached on the scale.

Retighten the lock knob by turning it clockwise.

TO USE THE TABLE EXTENSION

See Figure 31.

Increase the length of the saw table by using the table extension.

NOTE: The table extension cannot be extended if the rip fence is locked on the table rails.

Unlock the rip fence.

Unlock the table extension by lifting the table extension lock lever.

Extend the table extension as desired.

Lock the table extension by lowering the table extension lock lever.

LOCK

KNOB

	POSITIVE STOP	STOP PIN
	ADJUSTMENT SCREWS	STOP PIN
	ADJUSTMENT SCREWS
		Fig. 30
	TO UNLOCK	TABLE
		EXTENSION
		LOCK LEVER

TO LOCK	TABLE
	TABLE
	EXTENSION

Fig. 31

26

Image 26

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules  Guard Against Electrical Shock by Prevent Blade Coasts After Being Turned OFF Specific Safety Rules Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningExtension Cords Speed and WiringElectrical Grounding InstructionsGlossary of Terms Features Product SpecificationsKnow Your Table SAW See FigureSwitch Assembly Operating ComponentsLoose Parts List Tools NeededMounting Holes AssemblyUnpacking Release Lever Grips LEG Stand Center Brace To Open the LEG StandSee Figures 7 Wing NUT To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW WingTo close the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To move the leg standTo align the throat plate with the saw table To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate SET Screws Removing Throat PlateTo Check SAW Blade Installation To Install Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader To Check and Align the Blade Guard AssemblyOperation Causes of Kickback ApplicationsBasic Operation of the Table SAW Avoiding KickbackCross CUT Types of CutsCutting Tips Featherboard HOW to Mount a FeatherboardHOW to Make a Featherboard To USE the IND-I-CUT Disc To Change Blade DepthTo Change Blade Angle Once the Ind-I-Cut is levelTo USE the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence Back RIP FenceStop PIN To USE the Miter GaugeTo USE the Table Extension To UnlockRight Miter Gauge Groove Combination Square Aligning Screws Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Blade TOO Close to Miter Gauge GrooveSee Figures 35 Switch OFF Switch onMaking a Cross CUT Cross CUT Place Hands on Workpiece Miter Gauge Lock KnobRIP CUT Making a RIP CUTMaking a Miter CUT BladeSee Figures 39 HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT Viewed from the FRONT, below the Table SAWMaking a Bevel RIP CUT Supports Large Panel CUT Making a Compound Bevel Miter CUTMaking a Large Panel CUT Making a NON-THROUGH CUT Making a Dado CUT Dado CUTTo Replace the Blade AdjustmentsTo install a standard blade See Figures 46If blade is square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is not square to the tableScrew Lock Knob Miter Gauge ROD To Adjust the Miter GaugeBlade AT 45˚ Position Flat Head Screw SET ScrewSee Figures 54 To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail Locking LeverChecking the Table Extension To Adjust the Bevel Locking LeverTo Adjust the Table Extension Bevel Lock NUT Front HEX CouplingNylon SET Screw Adjustment MaintenanceGeneral Maintenance LubricationBrush CAP Assembly AccessoriesBrush Replacement Troubleshooting See To Check and Align the Blade GuardAdjustments section See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Bevel Stops at 0˚ and 45˚ SquaringPage What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS2410LS Serial No