RIDGID R250AFA manual Preparing the Tool for USE, Adjusting the Exhaust

Page 11

OPERATION

WARNING:

Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides.

PREPARING THE TOOL FOR USE

See Figure 2.

Under normal use conditions, the tool should be lubricated before connecting the tool to an air supply. Add air tool lubricant into the air fitting on the tool once daily with minimal use, or twice a day with heavy use. Only a few drops of oil at a time is necessary. Too much oil will only collect inside the tool and will be noticeable in the exhaust cycle.

Before connecting the tool, check the air compressor gauge to be sure it is functioning within the proper range of 70-120 psi.

NO-MAR PAD

See Figure 3.

The no-mar pad attached to the nose of the tool helps prevent marring and denting when working with softer woods.

WARNING:

Disconnect the tool from the air supply before removing or replacing the no-mar pad. Failure to do so could result in serious personal injury.

The pad can be removed by pulling it down and away from the nose. To replace the pad, fit it into place over the nose and push up at the back to reseat.

On-board storage for the pad is located on the magazine of the tool. An extra no-mar pad is provided in the on-board storage area.

ADJUSTING THE EXHAUST

See Figure 4.

The adjustable exhaust on the end cap of the tool allows the operator to direct the exhaust according to operator prefer- ence. To adjust, turn the exhaust cap until the exhaust blows in the desired direction.

AIR

FITTING

Fig. 2

NO-MAR PAD

STORAGE

NOSE

 

NO-MAR

 

PAD

Fig. 3

 

ADJUSTABLE

 

EXHAUST

Fig. 4

11

Image 11
Contents R250AFA OPERATOR’S ManualIntroduction Table of ContentsWork Area General Safety RulesPersonal Safety ServiceOperation Specific Safety RulesLoading Tool AIR Supply and ConnectionsSymbol Name DESIGNATION/EXPLANATION SymbolsActivate operating controls Glossary of TermsProduct Specifications FeaturesKnow Your Finish Nailer Adjustable ExhaustDepth of Drive Adjustment QUICK-CONNECT Swivel ConnectorPacking List AssemblyOperation UnpackingPreparing the Tool for USE Adjusting the ExhaustConnecting the Tool to AN AIR Supply See Figures 6 Loading the Tool with NailsContact Actuation Mode Using the Selectable TriggerSingle Sequential Actuation Mode Removing Nails from the Tool Setting the AIR PressureDrive Depth Adjustment Clearing a Jammed Fastener Accessories MaintenanceProblem Possible Cause Solution TroubleshootingWarranty Customer Service Information

R250AFA specifications

The RIDGID R250AFA is a powerful and versatile tool designed for professionals who require high performance in a pneumatic framing nailer. This unit is engineered to handle a variety of applications, making it an essential asset for contractors, builders, and DIY enthusiasts alike.

One of the standout features of the RIDGID R250AFA is its advanced drive technology. This pneumatic nailer utilizes a robust mechanism that delivers quick and consistent nail placement. This ensures that nails are securely fastened, providing the reliability needed in framing tasks. The tool is capable of driving 2 to 3-1/2 inch framing nails, accommodating different project requirements.

Another characteristic that sets the RIDGID R250AFA apart is its lightweight design. At just under 8 pounds, this nailer is easy to handle, which minimizes fatigue during long work sessions. The ergonomic grip and well-balanced body further enhance user comfort, allowing for precision and control in various positions and angles.

The RIDGID R250AFA also features a tool-free depth adjustment, enabling users to customize the depth of their nails effortlessly. This level of control is critical when working with different materials and ensures that nails are set flush with the surface, providing a professional finish.

The tool incorporates a selective actuation switch, which allows users to switch between bump and sequential firing modes. This flexibility makes it easier to adapt to different tasks, whether requiring rapid consecutive nailing or greater precision.

In terms of maintenance, the RIDGID R250AFA is equipped with a rear exhaust that helps direct air away from the user and the work area. This feature not only enhances comfort but also keeps the workspace cleaner by preventing debris from being blown around.

Safety is a priority with the RIDGID R250AFA as it comes with a safety tip that prevents accidental firing, ensuring user protection at all times. The magazine holds up to 70 nails, reducing downtime due to frequent reloading.

Ultimately, the RIDGID R250AFA is a robust and reliable framing nailer that combines performance, comfort, and safety. Whether it's for building frames, constructing decks, or any other nailing project, this tool is designed to meet the demanding needs of professionals in the construction industry.