Black & Decker BDL300S Assembly / SET-UP, Installing the Battery, Unfolding the Laser Legs

Page 3

586017-00 BDL300S laser 7/30/03 8:51 AM Page 3

INSTALLING THE BATTERY

Ensure laser on/off switch is in the left “OFF” position. Remove the battery compartment cover by pressing the tab of the cover in towards the center of the laser and out as shown in figure 3. Connect a fresh 9 volt alkaline battery making sure to match (+) and (-) terminals correctly. Replace the battery compartment cover.

ASSEMBLY / SET-UP

3

UNFOLDING THE LASER LEGS

 

4

To open the 360° Laser:

 

 

 

1.) Choose a relatively smooth and level surface away

 

from other work site activity to position the tripod.

 

2.) Unfasten the strap that is around the outside portion of

 

the laser and unfold the three sections of the laser

 

housing which become the legs of the tripod.

 

3.) Lock the legs in place, by pushing in on the top portion

 

of the hinge until it snaps into place as shown in figure 4.

 

CAUTION: Make sure tripod is secure and sitting

 

on a flat and stable surface.

 

 

ADJUSTING THE TRIPOD

5

6

The tripod is adjustable from its

 

 

lowest position of approximately 27

 

 

inches (686mm) shown in figure 5 to

 

 

a maximum height of 5 feet

 

 

(1524mm) shown in figure 6.

 

 

Extend any or all of the 5 sections of the tripod to reach the approximate desired height. Extend each section by gently sliding each tube out until it stops and then pull slightly harder on each section to lock.

When the approximate desired height is obtained, use the fine adjust knob shown in figure 8 to raise the laser to the final desired height. The fine adjustment knob will raise the laser up to an additional 7 inches (178mm) high.

First, loosen the lock knob as shown in figure 7.

Turn the fine adjust knob (figure 8) until the desired height is reached. Tighten the lock knob (fig. 7) to secure the tripod at the adjusted height.

7

Lock Knob

8

Fine Adjust

Knob

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents BDL300S Instruction ManualSafety Instructions Unfolding the Laser Legs Assembly / SET-UPInstalling the Battery Adjusting the TripodHanging the Laser Operating in Single 120˚ Laser ModeOperating in 360˚ Laser Mode Removing Laser from TripodService Information Full TWO-YEAR Home USE Warranty Problem Possible Cause SolutionMaintenance AccessoriesConsignes DE Sécurité Guide D’UTILISATIONAssemblage ET Installation Installation DE LA PileDéploiement DES Pattes DU Laser Réglage DU Trépied Retrait DU Laser Hors DU TrépiedSuspension DU Laser Mise EN Marche DU Laser Fonctionnement EN Mode Laser Simple DEFonctionnement EN Mode Laser DE Fonctionnement DU LaserGarantie Complète DE Deux ANS Pour Usage Résidentiel Problème Cause probable SolutionAccessoires Information SUR LES ServicesInstrucciones DE Seguridad Manual DE InstruccionesEnsamblaje / Montaje Instalación DE LA PilaCómo Extender LAS Patas DEL Láser Cómo Ajustar EL Trípode Cómo Separar EL Láser DEL TrípodeCómo Colgar EL Láser Funcionamiento DEL Láser BDL300S Problema Posible causa Solución586017-00 BDL300S laser 7/30/03 852 AM

BDL300S specifications

The Black & Decker BDL300S is a versatile and user-friendly stud finder designed for both DIY enthusiasts and professionals alike. This innovative tool streamlines the process of locating wooden studs, metal pipes, and live AC wires behind the walls, ensuring that your drilling and installation tasks are executed with precision and confidence.

One of the most notable features of the BDL300S is its advanced laser level functionality. This built-in feature allows users to have a clear horizontal or vertical reference line, making it ideal for hanging shelves, pictures, or installing cabinets. The laser level beams are bright and easy to see, even in well-lit rooms, providing an accurate guideline to follow.

The BDL300S is engineered with a user-friendly interface that includes a one-button operation. Simply press the button to begin scanning, and the tool will provide instant feedback on the location of studs or wires. This straightforward approach eliminates the guesswork, allowing users to work quickly and efficiently.

In terms of technology, the Black & Decker BDL300S utilizes a reliable electronic sensor system that delivers precise accuracy. This sensor can detect wooden studs up to 3/4 inch in depth and metal studs or pipes at varying depths, making it suitable for various wall constructions. The tool also features a built-in audio alert system that beeps when a stud or wire is detected, providing an auditory signal that complements the visual indicators.

The ergonomic design of the BDL300S ensures comfort during prolonged use. Its lightweight construction and easy-grip handle allow for extended operation without causing fatigue. The compact size makes it portable and easy to store, which is particularly advantageous for professionals who often work on different job sites.

Moreover, the device includes an LCD display that provides real-time visual feedback, indicating whether the user is over a stud or a live wire. This display enhances the overall user experience, combining simplicity with high functionality.

In conclusion, the Black & Decker BDL300S is an innovative tool that combines a stud finder with laser leveling capabilities, making it an essential addition to any toolbox. With features that prioritize accuracy, ease of use, and effective technology, it stands out as a reliable choice for skilled tradespeople and DIY home improvement projects alike. Whether you are hanging décor or performing renovations, the BDL300S offers a practical solution for achieving professional results.
Top Page Image Contents