Trouble shooting, Recommended accessories, Cause

trouble shooting

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE TROUBLE SHOOTaNG.

	TROUBLE		PROBABLE		CAUSE
Noisy	Operation	1.	incorrect	belt	tension
		2.	Dry Spindle
		3.	Loose spindle		pulley
			or motor	pulley.
Drill	Burns.	1.	Incorrect	speed
		2.	Chips not coming out
			of hole.
		3.	Dull Drill

4. Feeding too slow,

5, Not lubricated.

REMEDY

1.Adjust tension. See section "Getting To Know

Your Drill Press"...BELT TENSIONING ROD.

2. Lubricate

spindle. See "Lubrication"

section.

3. Tighten setscrews in pulleys.

1.Change speed. See section "Getting To Know

Your Drill Press"... DRILLING SPEED.

2.Retract drill frequently to clear chips.

3.Reshapen drill.

4.Feed fast enough...allow drill to cut.

5.Lubricate drill. See "Basic Dritl Press

Operation" section.

Drill leads off...

hole not round.

Wood splinters on

underside.

Workpiece torn loose from hand.

Drill Binds in

workpiece.

6. Drill running backwards.

I 1. Hard grain in wood or t lengths of cutting

lips and/or angles not equal.

1.No "back-up material" under workpiece.

1.Not supported or clamped properly.

1.Workpiece pinching drill or excessive feed

pressure.

6.Check motor rotation. See "Motor Specifications

and Electrical Requirements" section.

1.Resharpen drill correctly.

1. Use "back-up material"...See Basic Drill

Press Operation" section,

!, Support workpiece or clamp it...See-"Basic

Drill Press Operation" section.

1. Support workpiece	or clamp it...See	"Basic
Drill Press Operation"	section.

	2.	Improper		belt		tension,
Excessive drill	1,	Bent	drill.
runout or wobble.	2,	Worn	spindte			bearings.

	3.	Drill	not	properly
		installed		in	chuck.
	4.	Chuck	not		properly installed.

2. Adjust tension,..See	section "Getting	to Know
Your Drill Press"...BELT	TENSION	ROD.

1.Use a straight drill.

2.Replace bearings.

3.Install drill properly...See "Basic Drill Press Operation" section.

4.Install chuck properly...refer to "Unpacking

and Assembly Instructions"...INSTALLING	THE
CHUCK.

' I

I1'

'' I

iii

recommended accessories


Drills,	Shaper			Cutters, Router		Bits	See	Catalog
Rotary		Planer			.............................			9-2745
Mortising			Chisel		Housing			9-2465
Hollow		Chisels			and Mortising	Bits	See	Catalog
Dovetailing			Attachment					9- 2462
Shaper		Fence		Attachment				9-2487
Hold-Down			and		Guide			9-2457
Drill	Press		Vises		.......................		See	Catalog
Rotary		Table			.............................			9-2495


Tilt Table						9-243g
Cotlet	Chuck		.............................			9-24672
Shaper		Cutter	Adapter		.....................	9-24832
Sanding		Drum	......................			9-2497 - 9-2498
Hole	Saws up		to	21/= in. dia		See Catalog
Wire	Wheels up			to 4 in,	dia, max	See Catalog
Buffing		Wheels up to 4 in. dia. max				See Catalog
Polishing		Wheel,		1W'x	1 tn	9-64991
Column		Collar		............................		9-2438

The recommended accessories listed here are current and were available at the time this manual was pr;nted.