Sears 113.24611 manual Unpacking and checking, Additional safety instructions for drill presses

additional safety instructions for drill presses

11.Note and Follow the Safety Rules that Appear on the

Panel on the Left Side of the Head:

l DANGER: FOR YOUR OWN SAFETY: READ AND

UNDERSTANDOWNERS MANUALBEFORE

OPERATING THIS MACHINE. WEAR SAFETY

GOGGLES. DO NOT WEAR GLOVES. SECURELY

CLAMP WORK TO TABLE IF IT IS TOO SHORT TO

CONTACT THE COLUMN WHEN IN OPERATING POSITION.

12.Think Safety. Safety is a combination of operator common sense and alertness at all times when the drill pressis being used.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED FROM FREQUENT USE OF YOUR DRILL

PRESS) TO BECOME COMMONPLACE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A

SECOND IS SUFFICIENT TO iNFLiCT SEVERE INJURY.

unpacking and checking

						CONTENTS
								Page
General Safety Instructions for Power Tools								2
Additional		Safety			Instructions for		Drill Presses	3
Unpacking and Checking Contents							.................	4
Table of Loose Parts								4
Motor Specifications						and Electrical	Requirements	5
Assembly		....................................						6
Installing			the Chuck					6
Installing			Feed Handles					7
Installing			the Depth Stop					8
Installing			Motor		Pulley			9
Mounting the Motor								10
Installing			and Tensioning Belt					12
Getting to Know Your Drill Press							.................	12
Belt	Tension Rod					...........................		12
Drilling		Speed			..............................			12
On-Off		Switch			.............................			13
Removing			the Chuck					14
Drilling		to	Depth			...........................		15
Basic Drill		Press Operation						15
Installing			Drills		.............................			16
Positioning				Table		and Workpiece	...............	16
Feeding		...................................						17
Adjustments				.................................				17
Depth Scale				...............................				17
Quill	Return			Spring				17
Table and Head Lock Handles							.................	17
Quill	Bearing							17
Pinion Backlash						............................		18
Automatic			Feed Return					18
Maintenance				.................................				18
Lubrication			..................................					18
Recommended				Accessories				19
Trouble	Shooting				.............................			19
Repair	Parts			.................................				20

UNPACKING AND CHECKING CONTENTS

Your Craftsman Drill Press is shipped complete in one carton, lessmotor.

Separate all parts from packing materials and check each one with the "Table of Loose Parts" to make certain all

items are accounted for, before discarding any packing material.

If any parts are missing, do not attempt to assemble the drill press, plug in the power cord or turn the switch on until the missing parts are obtained and installed correctly.

Remove the protective oil that is applied to the table and

column. Use any ordinary household type grease and spot remover.

CAUTION: Never use gasoline, naptha or similar highly volatile solvents.

Apply a coat of automobile wax to the table. Wipe all parts thoroughly with a clean dry cloth.

contents

	TOOLS		NEEDED
		_	7/16	Inch Wrench
_;	....	-_	1/2	Inch Wrench

Key		TABLE				OF LOOSE PARTS
No.							Item		Qty.
1	Belt, V		...............................						1
2	Pulley,		Motor			(w!Set Screw)			1
3	Knob		................................						3
4	Rod	.................................							3
5	Mount,		Motor			.........................			1
6	Chuck,		Drill		...........................				1
	Bag of Miscellaneous Small Parts, Pt. # 71177
	Consisting				of	the Following:
7	Key,	Drill		Chuck			.......................		1
8	Carriage Bolt				(5/16-18 x 3/4)				4
9	Washer (11/32)					........................			4
10	Nut, Hex (5/16-18)						.....................		6
11	Tie,	Wire		.............................				inch)	1
12	SetScrew			Wrench			(5/32		1
13	SetScrew			Wrench			(1/4	inch)	1
14	Key,	Switch			...........................				2
15	Nut,	Stop		.............................					1
16	Pointer,		Depth			Gage			1
17	Shoe, Depth				Gage		......................		1
18	Screw, Thumb					.........................			1

4