Sears 113242502 owner manual Are, Thicknesses of Paper

Page 10

9. Holdrodwithonehandandwitha1/2in. wrench or

pliers start screwing on ONE of the nuts only A TURN OR TWO .... screw on other nut the same way

10_ Using TWO 1/2 in,, wrenches or pliers tighten both of the nuts,

IMPORTANT:

Apply

a coat

of

paste

wax to the top surface

and front

edge of

the

front

guide

bar,

This will

allow

the

fence to

slide

more

easily,

 

 

 

 

 

 

11o Slide

the

bars

so that screws

are

in

the MIDDLE

of

the

slotted

ho_eso

 

 

 

 

 

 

 

 

12.Position rip fence over miter gauge groove, holding up the rear end while engaging front end with bar o.. lower fence onto table°

!3,, Raise blade all the way up.

14. Carefully move fence against blade.

15, Move front bar until "0" mark on rip scale is

approximately in line with indicator°

16.Move FRONT bar upwards until fence is approximately 1/32 in,, above table .... tighten screw at left end of bar_,

NOTE: Fold a piece of newspaper making 8 thicknesses and place between rip fence and table to act as a spacer. This will hold the fence off of the table approx. 1/32 in,

17,, Adjust rear bar so that the fence is approximately 1/32 in, above table make sure it is square with fence guide bar rod .. , tighten screw at end of bar.

18,, Replace screws in rear of table extension .... be sure

top surface of extension is PARALLEL to top surface of rear guide bar,,

19_ Move fence to RIGHT edge of table .... make sure it is

approxo 1/32 in. above table at front and rear and tighten screws.

8THICKNESSES OF PAPER

8THICKNESSES OF PAPER

Io

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Table SAW Remove Adjusting Keys and Wrenches Full ONE Year Warranty on Craftsman Table SawsKnow Your Power Tool Keep Work Area Clean8o Kickbacks Adjustments ..... seeStability of SAW Stores Motor SpecificationsIndicated TypeTools LubricationUnpacking and Checking Contents Install In. longLoosen Blade SquarenessLock Installing RIP Fence Guide Bars AmongAre Thicknesses of PaperAligning RIP Fence Adlust Indicator Adjusting RIP Scale IndicatorIndicator Installing Blade GuardParallel 16 IN, WrenchIs on Right Always Lock IT Securely When in USEInsert When .SAWING .... USE Tilt Lock KnobArbor RemovingAgainst 1WORKPIECEEND Using the Miter GaugeWork Helpers Push StickRepetitive Cutting CrosscuttingStop Rods Compound Miter Cutting Miter CuttingBevel Crosscutting Not Attempt to Pick IT UP AS this could Endanger Your HandsPages 2, 3, RippingBevel Ripping RIPPING, Bevel RIPPING, ResawingCarefully Ploughing MoldingPush Block Cutting Panels Install Blade Guard Immediately UponResawing RabbetingIndicator Block Wrench Using FeatherboardsIndicator Block Miter GaugeGroove OFF and Remove Plug from Power Source OutletHeeling MarkedHead Combination Square Blade TILT, or Squareness Blade to TableTeeth TOP Screw Stop ScrevElevation Lock Elevation Lock Screw Lock NUT Screw Wrench Lock KnobElevation Worm and Teeth Tilt Worm and Teth GuardCAT., no CAT.. no Cut not true at Motor fails to develop Full power. PowerRemedy Elevation hand Wheel turn hardFrequent opening Fuses or circuit Breakers Motor starts slowly Or fails to come up To full speedStarting relay in motor will not Operate CausePage Parts List STDParts List for Craftsman 12-INCH Motorized Table SAW30494 Parts List for Craftsman 12-1NCH Motorized Table SAWPart 3540 63062Parts List for Craftsman 12-INCH Motorized Table SAW Key12 13 STDSwitch Assembly See Wiring DIAGRAM,62704 Miter Gauge Assembly Pert62594 Guard Assembly DescriptionExtension Parts List for Craftsman 12-INCH Iiotorized Table SAW62589 60323 STD 551225 * Lockwasher, Ext,r 1/4Service Inch Table SAW
Top Page Image Contents