FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.,
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state°
SEARS, ROEBUCK AND CO.., Seers Tower, BSC
,H,,,= | H | nnll inH | ==,= | ii =HI | i | i | i,J |
|
|
general safely insfrucfions
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool Learn its application and Fimitadons as well as the specific potential hazards peculiar to this tool.
2.GROUND ALL TOOLS
This tool is equipped with an approved L_conductor cord and a
3. KEEP GUARDS IN PLACE
in working order, and in proper adjustment and alignment,
4_ REMOVE ADJUSTING KEYS AND WRENCHES
Form habit of checking to see that keys and adjusting wrenches are removed from Iool before turning it on
5 KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents Floor must not be slippery due to wax or sawdust
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or expose them to rain Keep work area well lighted
Provide adequate surrounding work space
for power tools
protectors (plugs or muffs) during extended periods of operation.
13.SECURE WORK
Use clamps or a vise to hold work when practical It's safer than using your hand, frees both hands to operate too!
14.DON'T OVERREACH
Keep proper footing and balance at att times.
15, MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance Foftow instructions for lubricating and changing accessories
16. DISCONNECT TOOLS
before servicing; when changing accessories such as blades, bits, cutters, etc
17, AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plugging in
18, USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories Follow the instructions that accompany
the accessories The use of improper accessories may cause hazards
7. KEEP CHILDREN AWAY
AH visitors should be kept a safe distance from work area
8.MAKE WORKSHOP KID-PROOF
- with padlocks, master switches, or by removing starter keys
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting too_ is accidentally contacted
Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them
9. DON'T FORCE TOOL
It will do the job better and safer at the rate for which it was designed
10, USE RIGHT TOOL
Don't force toot or attachment to do a job it was not designed for
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) to get caught in moving parts,
Nonslip footwear is recommended Wear protective
hair covering to contain long hair Roll long sleeves above the elbow
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANS Z87,1) at
aH times,, Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses Atso, use face or dust mask if cutting operation is dusty, and ear
2& CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation A guard or other part that is damaged shoufd be property repaired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direction of rotation of the blade or cutter only
22, NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off Don't leave tool until it comes to a complete stop.