Sears 113242502 owner manual Ploughing Molding, Carefully, Push Block

Page 21

When "WIDTH OF RIP" is 2 in.. to 6 in. wide USE THE

PUSH STICK to feed the work.

When WIDTH OF RIP is NARROWER than 2 in., the push

stick CANNOT be used because the guard will interfere .

USE the AUXILIARY FENCE/WORK SUPPORT and

PUSH BLOCK.

Attach Auxiliary Fence/Work Support to rip fence with two "C" clamps..

AUXILIARY FENCE/

WORK SUPPORT

/t I

Feed the workpiece by hand along the AUXILIARY

FENCE/WORK SUPPORT until the end is approx_ 1 in. past

the front edge of the table. Continue to feed using the

PUSH BLOCK.

Hold the workpiece in position and install the PUSH

BLOCK by sliding it on top of the AUXILIARY

FENCE/WORK SUPPORT (This May Raise Guard)

BAFFLE

Narrow	strips	thicker	than the	Auxiliary	Fence/Work	CAREFULLY	raise	guard only enough to clear the
Support	may	enter	the guard	and strike	the baffle	workpiece Use PUSH		B LOCK to complete cut,,
					PLOUGHING	AND MOLDING

PLOUGHING is grooving with the grain the long way of the

workpJece, using the fence USE proper holddowns and feed devices.

MOLDING is shaping the workpiece with the grain the long

way of the workpiece, using the fence. Use proper

holddowns and feed devices

21

Image 21

Contents Table SAW Know Your Power Tool Full ONE Year Warranty on Craftsman Table SawsRemove Adjusting Keys and Wrenches Keep Work Area CleanAdjustments ..... see 8o KickbacksStability of SAW Indicated Motor SpecificationsStores TypeLubrication ToolsUnpacking and Checking Contents In. long InstallBlade Squareness LoosenLock Among Installing RIP Fence Guide BarsThicknesses of Paper AreAligning RIP Fence Indicator Adjusting RIP Scale IndicatorAdlust Indicator Installing Blade Guard16 IN, Wrench ParallelIs on Insert When .SAWING .... USE Always Lock IT Securely When in USERight Tilt Lock KnobRemoving ArborAgainst Work Helpers Using the Miter Gauge1WORKPIECEEND Push StickCrosscutting Repetitive CuttingStop Rods Bevel Crosscutting Miter CuttingCompound Miter Cutting Not Attempt to Pick IT UP AS this could Endanger Your HandsBevel Ripping RippingPages 2, 3, RIPPING, Bevel RIPPING, ResawingPloughing Molding CarefullyPush Block Resawing Install Blade Guard Immediately UponCutting Panels RabbetingIndicator Block Using FeatherboardsIndicator Block Wrench Miter GaugeHeeling OFF and Remove Plug from Power Source OutletGroove MarkedTeeth Blade TILT, or Squareness Blade to TableHead Combination Square TOP Screw Stop ScrevElevation Lock Screw Lock NUT Screw Wrench Lock Knob Elevation LockGuard Elevation Worm and Teeth Tilt Worm and TethCAT., no CAT.. no Remedy Motor fails to develop Full power. PowerCut not true at Elevation hand Wheel turn hardStarting relay in motor will not Operate Motor starts slowly Or fails to come up To full speedFrequent opening Fuses or circuit Breakers CausePage STD Parts ListTable SAW Parts List for Craftsman 12-INCH MotorizedPart Parts List for Craftsman 12-1NCH Motorized Table SAW30494 3540 63062Key Parts List for Craftsman 12-INCH Motorized Table SAWSTD 12 13See Wiring DIAGRAM, Switch AssemblyPert 62704 Miter Gauge AssemblyDescription 62594 Guard Assembly62589 60323 Parts List for Craftsman 12-INCH Iiotorized Table SAWExtension STD 551225 * Lockwasher, Ext,r 1/4Inch Table SAW Service