Barco R9001280 How to get a summary of your projector?

Controlling

7-4 5975348 BARCOVISION 8200 280497

How to get a summary of your projector?

The Summary gives an overview of :

- type of projector

- soft version

- lamp run time

- projector run time

- address

- installation configuration

- baud rate

- projector serial number

- lamp serial number

To display the Summary on the screen, press ENTER to start up the

Main

menu. Push the control disk up or down to highlight

System

Settings

and press ENTER to display the

System Settings

menu.

Push the control disk up or down to highlight

Summary

and press

ENTER. The summary will be displayed on the screen.

The following information is displayed :

-

type

of projector : BARCOVISION 8200

-

software version

-

Address

: to change the address of the projector, see Projector

Address above in this chapter.

-

Installation

: possible installations :

* Front/Ceiling

* Front/Table

* Rear/Ceiling

* Rear/Table

To change the installation configuration follow the instructions in

chapter Installation Set Up.

-

Baud rate

: transfer speed for communication with a IBM PC (or

compatible) or MAC. The baud rate of the projector must be the

same as the baud rate of the connected computer. When there is

a difference, consult Set up of the baud rate for communication with

a computer in chapter Connections.

-

Projector Run Time

: gives the total run time since the first start up.

All projectors leave the factory with a run time of approximately 24

hours.

-

lamp run time

: the total time the lamphas been used since it was

installed in the projector.

Attention : the total lifetime of the lamp for a safe operation is 1000

hours maximum. Do not use it longer. Always replace the lamp with

an original BARCO lamp kit.

-

Projector Serial number

: indicates the fabrication number of the

projector. This number can be useful when calling for technical

assistance.

-

Lamp Serial number

: indicates the fabrication number of the lamp.

This number can be useful when calling for technical assistance.

MAIN MENU

832b

Picture Control

Audio Control

System Settings

File service

Service Mode

SYSTEM SETTINGS

Lamp Control: 1500W

Installation

Input slots

Summary

Color

SUMMARY

Type : BARCOVISION 8200

Soft version : 1.00

Address : 1

Installation : front/ table

Baudrate : 9600

Projector run time : 104 h

Lamp run Time : 104 h

Projector Serial Number : 1012123

Lamp Serial Number : 0111111

Contents

Main Page BARCO PROJECTION SYSTEMS OWNER'S MANUAL Page Table of Contents TABLE OF CONTENTS i Table of Contents 1 Installation instructions Federal communication commission (FCC statement) General safety instructions. ON SAFETY Remarque sur la Scurit Instructions pour linstallation Fdral communication commission (FCC statement) Prescriptions de securite gnrales. SECURITE On Installation On Servicing On Cleaning On Repacking On illumination LInstallation Entretien et Rparation Nettoyage R-emballage Eclairage 2 Unpacking allow air circulation via the built-in dust filter at the bottom. Projector dimensions Pull To open Unpacking and Dimensions Battery installation in the RCU. Installation Guidelines 3 Installation guidelines * Environment * What about ambient light ? * Which screen type? Installation Guidelines * Where to install the projector? Definitions of the Abbreviation on drawings Lens type selection. Inputs and computer video format input compatibility : 4 6 Front panel terminology 7 8 11 Location and Functions of Control b. Remote control 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 5 Installation Set Up 6 Power (mains) cord connection Fuses Switching on Warning : Using a lamp for more than 1000 hours is dangerous, the lamp could explode. Input connections. Input module insertion into the projector : Switching to stand-by. Switching off Video/S-video input module ADJUST or ENTER EXIT Straps on module level. RGB analog input module. RGB input selection : ENTER RGB-SS [CV] RGB-SS [CS or HS&VS] Component input module. On Component input selection : Indication on the input slot menu : RGB3S/RG3sB input module. Input selection : Indication on the input slot menu : Set up of the baud rate for communication with a computer. Connecting a RCVDS 05 to the projector. Connecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projector. 7 How to use the RCU? Projector address a. hardware set up of the projector address. b. How to control the projector or projectors. How to display a projector address? How to program an address into the RCU? Picture controls with direct access. Brightness Control 'brightness' How to get source information? EXIT How to get a summary of your projector? Main Lamp Serial number Projector Serial number lamp run time 8 Input selection Installation of the settings for a input source. MAIN MENU LOAD FILE Edit file EDIT FILE "Vertical" "Horizontal" Read/Write Read AMDS Options EDIT FILE OPTIONS Vertical refresh [sync/async] Vertical sync polarity Rename Copy COPY FILE RENAME FILE Move MOVE FILE ENTER Delete DELETE FILE Page 9 Signal operations Screen operations Signal operations. MAIN MENU Gain adjustment per color Smoothness Still video [On/Off] Sync [Fast/Slow] ENTER Screen operations Picture Control "Picture" "Window" Zoom/Pan Page Picture Page Configure geometry Geometry Configure conversion Page SERVICE MODE How to activate the password function? Invalid Password Enter password Service mode Convergence adjustment of the LCD panels. Gaining access to the DIP switches Green Convergence Connections Test pattern Red on green Test pattern Blue on green Hatch Modify password 'Modify password' Reset Lamp Run Time Lamp Run Time History Lamp Run time History Reset Lamp Run Time Service Mode Standard Source Set Up Files STANDARD SOURCE SET UP FILES LACT : A Standard source set up files. Page Battery Replacement in the RCU BATTERY REPLACEMENT IN THE RCU B Battery replacement in the RCU. Lenses C moisten the cloth or tissue Focusing the lens Lens Cleaning Procedure Cleaning procedure for HD(1.5-3:1) lens and HD(3-5.3:1) lens. Lenses Lenses Source Numbers 90 - 99 D Source numbers 90 - 99 Insert Card INSERT CARD 5975348 BARCOVISION 8200 210497 RCU